- DeVILBISS - Sri PRO Lite - Service Manual - SB-E-2-512 - English [ English ]
Gravity Spray Gun for micro, smart repairs and
small areas.
DEVILBISS Sri PRO Series: SRi PRO Lite
II 2 G X
SERVICE MANUAL
IMPORTANT! DO NOT DESTROY
It is the Customer's responsibility to have all operators and service personnel read and understand
this manual.
Contact your local Binks representative for additional copies of this manual.
READ ALL INSTRUCTIONS BEFORE OPERATING THIS PRODUCT.
SB-E-2-512 R5.0 (05/2025) www.binks.com
EN
SPECIFICATIONS
AIR INLET PRESSURES
12 bar [175 psi]
Gun Air Inlet Pressure for High Efficiency and HVLP setups, with gun
triggered.
2.0 bar [29 psi]
FUNCTIONAL DESCRIPTION
The SRi PRO Lite spray gun is a professional quality gun designed with EPA compliant, high efficiency or high
volume, low pressure (HVLP) technology. HVLP technology reduces overspray and limits air cap pressure to 0.7
bar [10 psi]. High efficiency complies with EPA by obtaining transfer efficiency above 65%.
IMPORTANT: This spraygun is suitable for use with both waterbased and solvent based coating materials. The
gun is not designed for use with highly corrosive and/or abrasive materials and if used with such materials it
must be expected that the need for cleaning and/or replacement of parts will be increased. If there is any doubt
regarding the suitability of a specific material, contact your DeVilbiss Distributor or DeVilbiss direct.
ENVIRONMENTAL
Max Ambient Operating Temperature WITH CUP
MATERIALS OF CONSTRUCTION
Gun Body, Air Cap Retaining Ring, Knobs Anodised Aluminium
Vibration Level: <2.5 m/s²
Sound Power Level: Available on request
Sound Pressure Level: Available on request
Seals, Gaskets Solvent resistant
Trigger Chrome plated steel
Air Inlet, Body Bushing, Spreader Valve Body, Air Valve Nut Chrome plated brass
Air Cap Nickel plated brass
Fluid Tip, Fluid Needle and Trigger Stud Stainless Steel
Springs, Clips, Screws Stainless Steel
Fluid Inlet Size 7/16 - 14 UNC
GUN ONLY 395g
WEIGHT
Air Valve Assembly Stainless Steel, HDPE
CONNECTIONS
Air Inlet Size Universal 1/4 BSP and 1/4 NPS male
WITH CUP 455g
DIMENSIONS
L x H x W mm 135 x 252 x 18
P1 = Max Static Air Input Pressure
SB-E-2-512 R5.0 2/24 www.binks.com
EN
Product Description / Object of Declaration: SRiPro Lite
This Product is designed for use with: Solvent & Waterbased Materials
Suitable for use in hazardous area: Zone 1/Zone 2
This Declaration of Conformity / Incorporation is issued
under the sole responsibility of the manufacturer:
Binks U.K. Limited,
Ringwood Road,
Bournemouth, BH11 9LH. UK
Representative authorised to compile the technical file President @. Binks France SAS
5 Place Pierre Semard, 94130 Nogent sur Marne , Paris, France
EU Declaration of Conformity
Protection Level: II 2 G X/Ex h II Gb X
Notified body details and role: Element Materials Technology Rotterdam B.V. (2812)
Lodging of ATEX Technical file
This Declaration of Conformity / Incorporation is issued under the sole responsibility of the
manufacturer:
Machinery Directive 2006/42/EC
ATEX Directive 2014/34/EU
by complying with the following statutory documents and harmonised standards:
EN ISO 12100:2010 Safety of Machinery - General Principles for Design
BS EN 1953:2013 Atomizing and spraying equipment for coating materials - Safety requirements
EN ISO 80079-36:2016 Explosive Atmospheres- Part 36:Non Electrical equipment for explosive atmospheres-Basic methods
and requirements.
EN ISO 80079-37:2016 Explosive Atmospheres- Part 37: Non Electrical equipment for explosive atmospheres - protection by
methods c, b and k.
EN 1127-1:2019 Explosive atmospheres - Explosion prevention - Basic concepts
HVLP and High Efficiency products comply with the requirements of PG6 from the EPA guidelines and offer greater than 65%
transfer efficiency.
Providing all conditions of safe use / installation stated within the product manuals have been complied with and also installed in accordance
with any applicable local codes of practice.
Signed for and on behalf of Binks
U.K. Ltd:
Executive President: Engineering and
Operations, Shoreview, MN, 55126. USA
F. A. Sutter
Document Part No.
. 09/04/25
SB-E-2-512 R5.0 3/24 www.binks.com
EN
Product Description / Object of Declaration: SRi PRO LITE
This Product is designed for use with: Solvent & Waterbased Materials
Suitable for use in hazardous area: Zone 1/Zone 2
This Declaration of Conformity / Incorporation is issued
under the sole responsibility of the manufacturer:
Binks U.K. Limited,
Ringwood Road,
Bournemouth, BH11 9LH. UK
UKCA Declaration of Conformity
Protection Level: II 2 G X/Ex h II Gb X
Approved body details and role: Element Materials Technology Warwick Ltd. UK. (0891)
Lodging of UKEX Technical file
This Declaration of Conformity / Incorporation is issued under the sole responsibility of the
manufacturer:
Supply of Machinery (Safety) Regulations 2008
Equipment and Protective Systems Intended for use in Potentially Explosive Atmospheres Regulations 2016
by complying with the following statutory documents and designated standards:
BS EN ISO 12100:2010 Safety of Machinery - General Principles for Design
BS EN 1953:2013 Atomizing and spraying equipment for coating materials - Safety requirements
BS EN ISO 80079-36:2016 Explosive Atmospheres- Part 36:Non Electrical equipment for explosive atmospheres-Basic
methods and requirements.
BS EN ISO 80079-37:2016 Explosive Atmospheres- Part 37: Non Electrical equipment for explosive atmospheres - protection
by methods c, b and k.
BS EN 1127-1:2019 Explosive atmospheres - Explosion prevention - Basic concepts
Providing all conditions of safe use / installation stated within the product manuals have been complied with and also installed in accordance
with any applicable local codes of practice.
Signed for and on behalf of Binks
U.K. Ltd:
Executive President: Engineering and
Operations, Shoreview, MN, 55126. USA
F. A. Sutter
Document Part No.
. 09/04/2025
SB-E-2-512 R5.0 4/24 www.binks.com
ENIn this part sheet, the words WARNING, CAUTION and NOTE are used to emphasise important safety information as
follows:
WARNING CAUTION NOTE
Hazards or unsafe practices which could result in
severe personal injury, death or substantial
property damage.
Hazards or unsafe practices which could result in
minor personal injury, product or property
damage.
Important installation, operation or maintenance
information.
FIRE AND EXPLOSION HAZARD. Never use 1,1,1-Trichloroethane,
Methylene Chloride, other Halogenated Hydrocarbon solvents or fluids
containing such solvents in equipment with aluminium wetted parts. Such use
could result in a serious chemical reaction, with the posibility of explosion.
Consult your fluid suppliers to ensure that the fluids being used are compatible
with aluminium parts.
GLOVES. Must be worn when spraying or cleaning the
equipment.
WEAR SAFETY GLASSES. Failure to wear safety glasses with
side shields could result in serious eye injury or blindness.
STATIC CHARGE. Fluid may develop a static charge that must be dissipated
through proper grounding of the equipment, objects to be sprayed and all other
electrically conductive objects in the dispensing area. Improper grounding or
sparks can cause a hazardous condition and result in fire, explosion or electric
shock and other serious injury.
WEAR RESPIRATOR. The use of respiratory protective
equipment is recommended at all times. The type of equipment
must be compatible with the material being sprayed.
WARNING
Read the following warnings before using this equipment.
SOLVENTS AND COATING MATERIALS. Can be highly flammable or
combustible when sprayed. Always refer to the coating supplier's instructions
and safety sheets before using this equipment.
INSPECT THE EQUIPMENT DAILY. Inspect the equipment for
worn or broken parts on a daily basis. Do not operate the
equipment if you are uncertain about its condition.
READ THE MANUAL. Before operating finishing equipment, read and
understand all safety, operation and maintenance information provided in the
operation manual. Users must comply with all local and national codes of
practice and insurance company requirements governing ventilation, fire
precautions, operation and house-keeping of working areas.
EQUIPMENT MISUSE HAZARD. Equipment misuse can cause
the equipment to rupture, malfunction or start unexpectedly and
result in serious injury.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PROVIDE THIS INFORMATION TO THE OPERATOR OF THE EQUIPMENT.
TOXIC VAPOURS. When sprayed, certain materials may be poisonous, create
irritation, or are otherwise harmful to health. Always read all labels, safety
sheets and follow any recommendations for the material before spraying. If in
doubt contact your material supplier.
NEVER MODIFY THE EQUIPMENT. Do not modify the
equipment unless the manufacturer provides written approval.
LOCK OUT / TAG-OUT. Failure to de-energise, disconnect, lock out and tag-
out all power sources before performing equipment maintenance could cause
serious injury or death.
PROJECTILE HAZARD. You may be injured by venting liquids or
gases that are released under pressure, or flying debris.
NOISE LEVELS. The A-weighted sound level of pumping and spray equipment
may exceed 85 dB(A) depending on equipment settings. Actual noise levels
are available on request. It is recommended that ear protection is worn at all
times while equipment is in use.
PRESSURE RELIEF PROCEDURE. Always follow the pressure
relief procedure in the equipment instruction manual.
KNOW WHERE AND HOW TO SHUT OFF THE EQUIPMENT
IN CASE OF AN EMERGENCY.
HIGH PRESSURE CONSIDERATION. High pressure can cause serious
injury. Relieve all pressure before servicing. Spray from the gun, hose leaks or
ruptured components can inject fluid into your body and cause extremely
serious injury.
OPERATOR TRAINING. All personnel must be trained before
operating finishing equipment.
SB-E-2-512 R5.0 5/24 www.binks.com
EN
TE5
HV5
RS1
MC1
L - TE5 - 10
L
(L/Min)
TE5
RS1
MC1
0.6mm 0.8mm 1.0mm 1.2mm 1.4mm
TE5 - S S S S
HV5 - S S S S
RS1 - S S S S
MC1 S - - - -
SRi PRO LITE - GUN PART NUMBER FORMAT & PART SELECTION GUIDE
AIR CAP FLUID TIP
High Efficiency Size & construction
SRi PRO
Lite
Air Cap & Type Part Number Air Consumption
Recommended
Air Inlet Pressure
Typical Fluid
Flow*
Typical Fan
Pattern Size**
HVLP See table 2
Round Spray
High Efficiency
See table 1
180mm
HV5 HVLP SRIPRO-102-HV5-K 135 [4.8 cfm] 2 Bar [29 psi] 5 - 80 ml/min 160mm
High Efficiency SRIPRO-102-TE5-K 100 [3.5 cfm] 2 Bar [29 psi] 5 - 100 ml/min
50mm
High Efficiency SRIPRO-102-MC1-K 50 [1.8 cfm] 1 Bar [14.5 psi] 1 - 50 ml/min 60mm
Round Spray SRIPRO-102-RS1-K 55 [1.9 cfm] 2 Bar [29 psi] 5 - 50 ml/min
SRIPRO-300-12-14-K
06 SRIPRO-210-06M-K SRIPRO-310-06M-K
08 SRIPRO-200-08-K SRIPRO-300-08-10-K
TABLE 2 - FLUID TIPS & NEEDLES
Fluid Tip Size
Stainless Steel
Fluid Tip Needle
S= High quality stainless steel tips & needles available in this type & size.
TABLE 1 - AIR CAP PERFORMANCE GUIDE
TABLE 3 - RECOMMENDED FLUID TIP / AIR CAP COMBINATIONS
* Flow rates may vary according to paint/material and pressure used.
** Fan pattern size @ 50 - 100mm distance.
Air Cap & Type
High Efficiency
HVLP
Round Spray
High Efficiency
14 SRIPRO-200-14-K SRIPRO-300-12-14-K
10 SRIPRO-200-10-K SRIPRO-300-08-10-K
12 SRIPRO-200-12-K
SB-E-2-512 R5.0 6/24 www.binks.com
EN
EXPLODED VIEW
SB-E-2-512 R5.0 7/24 www.binks.com
EN
PARTS LIST
REF. PART No. DESCRIPTION QTY.
1 - RETAINING RING 1
2
4 - RETAINING RING SEAL 1
5 SEE TABLE 1 AIR CAP & RETAINING RING 1
- SLIP RING 1
3 - AIR CAP 1
*8 - BODY BUSHING SEAL 1
9 - BODY BUSHING 1
6 SEE TABLE 2 FLUID TIP & SEPARATOR 1
*7 SRIPRO-2-K5 SEPARATOR (KIT OF 5) 1
*12 - NEEDLE SPRING 1
*13 - NEEDLE SPRING PAD 1
10 SN-6-K BODY BUSHING & SEAL 1
11 SEE TABLE 2 FLUID NEEDLE 1
16 - CIRCLIP 1
17 - SPREADER VALVE BODY 1
14 SN-81-K FLUID ADJUSTING KNOB 1
15 SN-423-K3 SPRING & PAD (KIT OF 3) 1
20 SRIPRO-402-K SPREADER VALVE ASSEMBLY 1
21 - NEEDLE PACKING 1
*18 - SPREADER VALVE SEAL 2
19 - SPREADER VALVE ADJUSTING KNOB 1
*24 SN-404-K PACKING, SPRING & PACKING NUT KIT 1
25 - AIR VALVE BODY 1
22 - PACKING SPRING 1
23 - PACKING NUT 1
28 - AIR VALVE SPRING 1
29 - AIR VALVE SPRING PAD 1
26 - AIR VALVE CAGE 1
27 - AIR VALVE POPPET 1
*32 - TRIGGER STUD SCREW (T20 TORX) 1
33 - TRIGGER 1
30 - AIR VALVE SEAL 1
31 SN-402-K AIR VALVE ASSEMBLY 1
36 SN-405-K5 STUD AND SCREW KIT (KIT OF 5) 1
37 - AIR INLET KIT 1
*34 - TRIGGER STUD 1
35 SN-42-K TRIGGER STUD & SCREW KIT 1
SB-E-2-512 R5.0 8/24 www.binks.com
EN
PARTS LIST (Continued)
REF. PART No. DESCRIPTION QTY.
38 - COLOUR ID RING KIT (4 COLOURS) 1
*39 -
41 - VALVE ADJUSTING KNOB 1
*42 - VALVE PIN 1
CIRCLIP 1
40 - VALVE BODY 1
45 SRI-414-K2 GRAVITY CUP LID (KIT OF 2) 1
46 SRI-42-K3 FILTER (KIT OF 3) 1
43 PRO-408-K AIRFLOW VALVE 1
44 GFC-2-K5 DRIP CHECK LID (KIT OF 5) 1
49 SPN-8-K2 TORX DRIVER (KIT OF 2) 1
50 SRI-50-K2 SPANNER (KIT OF 2) 1
47 - GRAVITY CUP 1
48 SRI-510 GRAVITY CUP KIT 1
SERVICE PARTS
- PRO-415-1 SPRAY GUN REPAIR KIT (INCLUDES ITEMS MARKED *)
CAUTION
51 SRI-51-K12 FUNNEL (KIT OF 12) 1
52 - AIR VALVE SERVICE TOOL 1
IMPORTANT: This spraygun is suitable for use with both waterbased and solvent based coating
materials.
If there is any doubt regarding the suitability of a specific material, contact your DeVilbiss Distributor
or Binks direct.
● The gun is not designed for use with highly corrosive and/or abrasive materials.
● To avoid premature degradation of parts, DeVilbiss recommends the gun is washed in neutral
cleaning solution (pH 6 to 8).
● The gun is not designed to be cleaned within an ultrasonic bath.
SB-E-2-512 R5.0 9/24 www.binks.com
EN
1. Connect the gun to a clean, moisture and oil free air supply using a conductive hose.
2. Mix coating material to Manufacturer's instructions and strain material.
3. Turn fluid adjusting knob (14) clockwise to prevent fluid needle movement.
4. Turn spreader valve adjusting knob (19) counter clockwise to fully open.
5. Adjust inlet air pressure if required.
6. Turn fluid adjusting knob counter clockwise until first thread shows.
7. Test spray. If the finish is too dry, reduce airflow by reducing air inlet pressure.
8. If finish is too wet, reduce fluid flow by turning fluid adjusting knob (14) clockwise. If atomisation
is too coarse, increase air inlet pressure. If too fine, reduce inlet pressure.
9. The pattern size can be reduced by turning spreader valve knob (19) clockwise.
10. Hold gun perpendicular to surface being sprayed. Arcing or tilting may result in uneven coating.
11. The recommended spray distance is 50-100mm.
12. Spray edges first. Overlap each stroke a minimum of 75%. Move gun at a constant speed.
13. Always turn off air supply and relieve pressure when gun is not in use.
WARNING
The spray gun must be earthed to dissipate any electrostatic charges which may be created by fluid
or air flows. This can be achieved through the spray gun mounting, or conductive air/fluid hoses.
Electrical bond from the spray gun to earth should be checked and a resistance of less than 10⁶ Ohms
is required.
START-UP SEQUENCE
SB-E-2-512 R5.0 10/24 www.binks.com
EN
NOTE
Depending on hose length, larger I.D. hose may be required. Install an air gauge at the gun handle.
When gun is triggered on, adjust regulated pressure as required. Do not use more pressure than is
necesarry to atomise the material being applied. Excess pressure will create additional overspray and
reduce transfer efficiency.
Order for disassembly
- see over page
(reverse for assembly)
(reverse for assembly)
- see over page
SPRAY GUN DISASSEMBLY / ASSEMBLY
KEY
NOTE
If quick connect couplings are required, use only high flow quick connects. Other types will not flow
enough air for correct gun operation.
SPRAY GUN MAINTENANCE & CLEANING
To clean air cap and fluid tip, brush exterior with a stiff bristle brush. If necesarry to clean cap holes,
use a broom straw or toothpick if possible. If a wire or hard instrument is used, extreme care must
be taken to prevent scratching or burring of the holes which will cause a distorted spray pattern.
To clean fluid passages, remove excess material, then flush with gun wash solution. Wipe the gun
exterior with a dampened cloth. Never completely immerse in any solvent or cleaning solutions as
this is detrimental to the lubricants and life of the spray gun.
#
#
SB-E-2-512 R5.0 11/24 www.binks.com
EN
NOTE
When replacing the fluid tip or fluid needle, replace tip, needle and fluid packing at the same time.
Using worn parts can cause fluid leakage. Do not overtighten.
CAUTION
To prevent damage to fluid tip or fluid needle, be sure to either:
1. Pull the trigger and hold while tightening or loosening the fluid tip, or,
2. Remove the fluid adjusting knob to relieve spring pressure against needle collar.
DISASSEMBLY TIP & NEEDLE
SB-E-2-512 R5.0 12/24 www.binks.com
EN
DISASSEMBLY AIR VALVE
SB-E-2-512 R5.0 13/24 www.binks.com
EN
DISASSEMBLY / ASSEMBLY AIR VALVE SEALS
SB-E-2-512 R5.0 14/24 www.binks.com
EN
DISASSEMBLY PACKING
SB-E-2-512 R5.0 15/24 www.binks.com
EN
TROUBLESHOOTING MECHANICAL PERFORMANCE
GENERAL FAULTS CAUSE CORRECTION
Will not spray.
No air pressure at gun. Check air supply and air line.
Fluid needle adjustment knob
not open enough.
Open fluid needle adjustment
knob.
Gun spits paint when triggering
on due to paint build-up inside
air cap between spraying
operations.
Fluid tip not fitted correctly in
gun head.
Tighten.
Fluid tip/needle leakage. Check for damage or blockage.
Gun spits paint when triggering
on and off.
Incorrect needle fitted to gun.
Check fluid tip/needle selection
chart and fit correct item.
Excessive needle wear. Replace with new needle.
Excessive fluid tip wear. Replace with new fluid tip.
Paint build-up on air cap.
Damaged air cap holes. Replace with new air cap.
Gradual build-up of bounce-back
on gun head.
Thoroughly clean.
Paint build-up on fluid tip.
Fluid tip not fitted correctly in
gun head.
Tighten.
Fluid tip/needle leakage. Check for damage or blockage.
Unable to get round spray
Fluid tip or sprayhead incorrectly
fitted.
Remove, check components for
damage and refit correctly.
SB-E-2-512 R5.0 16/24 www.binks.com
EN
Slow fluid leak from fluid tip and
needle seat.
Fluid tip internal seat scored
damaged or worn.
Replace.
Fluid needle external profile
damaged or worn.
Replace.
Contamination on needle or tip
mating surfaces preventing good
seal.
Thoroughly clean.
Incorrect fluid tip for fluid needle
fitted to gun.
Check tip/needle selection chart
and fit correct item.
Sluggish needle. Lubricate packing. (GL-1)
Tight packing nut. Adjust.
Major fluid leak or fluid jetting
from fluid tip and needle seat.
Contamination on needle or tip
mating surfaces preventing good
seal.
Remove tip and needle and
thoroughly clean.
Incorrect fluid tip for fluid needle
fitted to gun.
Check tip/needle selection chart
and fit correct item.
When removing air cap from retaining ring, do not remove the ring seat from the retaining ring.
Damage to the parts may occur. Simply wipe parts clean and reassemble with new or clean air cap.
FLUID FAULTS CAUSE CORRECTION
Slow fluid leak from needle
packing.
Fluid needle packing worn or
loose.
Tighten or replace as necessary.
SB-E-2-512 R5.0 17/24 www.binks.com
EN
Small air leak from air cap when
gun is not triggered.
Air Valve Stem contaminated
and not correctly seating.
Remove Air Valve Stem and
thoroughly clean valve shaft and
seating surfaces.
Air Valve Stem seal damaged or
missing.
Replace.
AIR FAULTS CAUSE CORRECTION
SB-E-2-512 R5.0 18/24 www.binks.com
EN
TROUBLESHOOTING SPRAY PERFORMANCE
CONDITION CAUSE CORRECTION
Heavy top or bottom pattern.
Material build-up on air cap,
plugged horn holes, centre holes or
jets.
Soak cap or tip in suitable solvent
and thoroughly clean.
Material build-up on fluid tip exterior
or partially plugged fluid tip.
Replace fluid tip or air cap if
necessary.
Fluid tip or cap dirty or damaged.
Replace fluid tip or air cap if
necessary.
Remedies for the top-heavy, bottom-heavy, right-heavy and left-heavy patterns.
Determine if the obstruction is on the air cap or the fluid tip. Do this by making a test spray pattern. Then, rotate
the cap one-half turn and spray another pattern. If the defect is inverted, obstruction is on the air cap. Clean the
air cap as previously instructed. Also check for dried paint just inside the cap centre hole opening, remove by
washing with solvent.
If the defect is not inverted, it is on the fluid tip. Clean tip. If problem persists, renew tip.
Heavy right or left
side pattern.
Left or right side horn holes plugged.
Soak cap or tip in suitable solvent
and thoroughly clean.
Dirt or damage on left or right side
of fluid tip exterior.
Replace fluid tip or air cap if
necessary.
SB-E-2-512 R5.0 19/24 www.binks.com
EN
Heavy centre pattern.
Pattern adjustment valve set too low.
Turn out counter clockwise to
achieve correct pattern.
Too much material.
Reduce fluid flow by turning fluid
needle adjusting screw clockwise.
Reduce fluid pressure.
Material too thick. Thin to correct consistency.
Atomising air pressure too low. Increase air pressure.
Intermittent or 'fluttering'
spray fan. Loose fluid tip. Tighten.
Fluid tip not seated correctly in gun
head.
Remove fluid tip, clean components,
check cone seating on tip and gun
for damage or contamination.
Too high horn pressure.
Reduce air pressure by rotating
pattern control valve clockwise.
Too much air for fluid quanitity used. Reduce input air pressure.
Partially obstructed fluid passage or
hose.
Clean or replace.
Split spray pattern
Not enough material flow.
Increase fluid flow by changing fluid
tip size, opening needle control knob
or increase fluid pressure on
pressure feed container.
SB-E-2-512 R5.0 20/24 www.binks.com
EN
Ball end heavy
pattern.
Too much fluid flow.
Change fluid tip for smaller size or
change air cap for different
specification air cap.
Adjust gun or reduce fluid pressure.
Material too thin.
Mix properly or apply light
coats/reduce fluid flow.
Gun tilted at an angle. Mount gun at right angle to work.
Excessive bounce-back.
Too much atomisation air pressure. Reduce air pressure.
Gun too far from surface.
Check distance (normally 150-
200mm).
Thin, sandy coarse finish drying
before it flows out.
Gun too far from surface. Check distance.
Too much air pressure.
Reduce air pressure and check spray
pattern.
Fluid flow too low.
Increase fluid flow by changing fluid
tip size, supply pressure or turning
needle control knob counter
clockwise.
Runs and sags.
Too much fluid flow.
SB-E-2-512 R5.0 21/24 www.binks.com
EN
DIMENSIONS
SB-E-2-512 R5.0 22/24 www.binks.com
EN
WARRANTY POLICY
This product is covered by Binks materials and workmanship limited warranty.
The use of any parts or accessories, from a source other than Binks, will void all warranties. Failure to
reasonably follow any maintenance guidance provided, may invalidate any warranty.
For specific warranty information please contact Binks.
For technical assistance or to locate an authorised distributor, contact one of our international sales and
customer support locations below.
REGION BINKS CONTACT
Americas Tel: 1-888-992-4657
Europe, Africa, Middle East Tel: +44 (0)1202 571 111
India
Japan Tel: +81 45 785 6421
Australia Tel: +61 (0) 2 8525 7555
WARRANTY PAGE
marketingroa@binks.com
China Tel: +8621-3373 0108
Korea Tel: +82313663303
SB-E-2-512 R5.0 23/24 www.binks.com
EN
© 2025 Binks US, LLC. All rights reserved.
Binks is a global leader in innovative finishing technologies. Binks reserves the right to modify equipment
specifications without prior notice.
Binks®, DeVilbiss®, and Ransburg® are registered trademarks of Binks US, LLC.
SB-E-2-512 R5.0 24/24 www.binks.com
