- Pneumatic Drum Elevator Manual 77-3312 [ English ]
77-3312
DE-05 & DE-10
Pneumatic Drum Elevator
DE-05
DE-10
EN
It is the Customer's responsibility to have all operators and service personnel read and
understand this manual.
Contact your local Binks representative for additional copies of this manual.
READ ALL INSTRUCTIONS BEFORE OPERATING THIS PRODUCT
ADDITIONAL RESOURCES
For additional information or copies of your service manual, please visit us online at:
binks.com/en/library
Or use this QR code with your mobile device:
XXXXXXXX
Insert
QR
code
Obey local or municipal regulations for product recycling and disposal.
IMPORTANT! DO NOT DESTROY
77-3312 R3.0 (06/2025) 2/28 www.binks.com
EN
by complying with the following statutory documents and harmonised standards:
EU Declaration of Conformity
Product Description / Object of Declaration:
This Product is designed for use with: Solvent & Waterbased Materials
Notified body details and role: Element Materials Technology Rotterdam B.V. (2812)
Lodging of ATEX Technical file
This Declaration of Conformity / Incorporation is issued
under the sole responsibility of the manufacturer:
Binks U.K. Limited,
Ringwood Road,
Bournemouth, BH11 9LH. UK
Pneumatic Elevator 104112, 104153, 104154, 104155, DE-05, DE-
10, DE-12, DE-15.
Suitable for use in hazardous area: Zone 1/Zone 2
Protection Level: II 2 G X T4
This Declaration of Conformity / Incorporation is issued under the sole responsibility of the
manufacturer:
Executive President: Engineering and
Operations, Shoreview, MN, 55126. USA
F. A. Sutter
12/06/25
Providing all conditions of safe use / installation stated within the product manuals have been complied with and also installed in accordance
with any applicable local codes of practice.
Signed for and on behalf of Binks
U.K. Ltd:
Document Part No.
.
77-3312 R3.0 (06/2025) 3/28 www.binks.com
EN
Product Description / Object of Declaration:
Element Materials Technology Warwick Ltd. UK. (0891)
by complying with the following statutory documents and designated standards:
Providing all conditions of safe use / installation stated within the product manuals have been complied with and also installed in accordance
with any applicable local codes of practice.
F. A. Sutter
12/06/25
This Declaration of Conformity / Incorporation is issued under the sole responsibility of the
manufacturer:
Pneumatic Elevator 104112, 104153, 104154, 104155, DE-05, DE-
10, DE-12, DE-15.
Suitable for use in hazardous area: Zone 1/Zone 2
Protection Level: II 2 G X T4
Approved body details and role:
Lodging of UKEX Technical file
This Declaration of Conformity / Incorporation is issued
under the sole responsibility of the manufacturer:
Binks U.K. Limited,
Ringwood Road,
Bournemouth, BH11 9LH. UK
Signed for and on behalf of Binks
U.K. Ltd:
Executive President: Engineering and
Operations, Shoreview, MN, 55126. USA
This Product is designed for use with: Solvent & Waterbased Materials
UKCA Declaration of Conformity
Document Part No.
.
77-3312 R3.0 (06/2025) 4/28 www.binks.com
ENIn this part sheet, the words WARNING, CAUTION and NOTE are used to emphasize important safety information as
follows:
WARNING CAUTION NOTE
Hazards or unsafe practices which could result in
severe personal injury, death or substantial property
damage.
Hazards or unsafe practices which could result in
minor personal injury, product or property
damage
Important installation, operation or maintenance
information.
WARNING
Read the following warnings before using this equipment.
READ THE MANUAL. Before operating finishing equipment, read and
understand all safety, operation and maintenance information
provided in the operation manual.
AUTOMATIC EQUIPMENT. Automatic
equipment may start suddenly without
warning.
WEAR SAFETY GLASSES. Failure to wear safety glasses with side
shields could result in serious eye injury or blindness.
PROJECTILE HAZARD. You may be
injured by venting liquids or gases that
are released under pressure, or flying
debris.
DE-ENERGIZE, DE-PRESSURISE, DISCONNECT AND LOCK OUT ALL
POWER SOURCES DURING MAINTENANCE. Failure to de-energize,
disconnect and lock out all power supplies before performing
equipment maintenance could cause serious injury or death. KNOW WHERE AND HOW TO SHUT
OFF THE EQUIPMENT IN CASE OF AN
EMERGENCY.
NOISE LEVELS. The A-weighted sound level of pumping and spray
equipment may exceed 85 dB(A) depending on equipment settings.
Actual noise levels are available on request. It is recommended that
ear protection is worn at all times while equipment is in use.
INSPECT THE EQUIPMENT DAILY. Inspect the equipment for worn or
broken parts on a daily basis. Do not operate the equipment if you
are uncertain about its condition.
OPERATOR TRAINING. All personnel
must be trained before operating
finishing equipment.
EQUIPMENT MISUSE HAZARD. Equipment misuse can cause the
equipment to rupture, malfunction or start unexpectedly and result in
serious injury. PACEMAKER WARNING. You are in the
presence of magnetic fields which may
interfere with the operation of certain
pacemakers.HIGH PRESSURE CONSIDERATION. High pressure can cause serious
injury. Relieve all pressure before servicing. Spray from the gun,
hose leaks or ruptured components can inject fluid into your body
and cause extremely serious injury.
KEEP EQUIPMENT GUARDS IN PLACE.
Do not operate the equipment if the
safety devices have been removed.
STATIC CHARGE. Fluid may develop a static charge that must be
dissipated through proper grounding of the equipment, objects to be
sprayed and alll other electrically conductive objects in the dispensing
area. Improper grounding or sparks can cause a hazardous condition
and result in fire, explosion or electric shock and other serious injury.
NEVER MODIFY THE EQUIPMENT. Do
not modify the equipment unless the
manufacturer provides written
approval.
PROP 65 WARNING. WARNING: This product contains chemicals
known to the state of California to cause cancer and birth defects or
other reproductive harm.
PINCH POINT HAZARD. Moving parts
can crush and cut. Pinch points are
any areas where ther are moving
parts.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PROVIDE THIS INFORMATION TO THE
OPERATOR OF THE EQUIPMENT.
PRESSURE RELIEF PROCEDURE.
Always follow the pressure relief
procedure in the equipment instruction
manual.
77-3312 R3.0 (06/2025) 5/28 www.binks.com
EN
D
DE-05 = 500mm [19.7]
DE-10 = 955mm [37.6]
3 bar [44 psi]
7 bar [100 psi]
A G1/2'' BSPP Female
B
DE-05 = 50kg [110 lbs]
DE-10 = 75kg [165 lbs]
C
DE-05 = 300mm [11.8]
DE-10 = 375mm [14.8]
<1Ω
DE-05DB = 51kg [112 lbs]
DE-10DK = 80kg [154 lbs]
0 - 40°C [32 - 104°F]
Dimension
DE-05 DE-10
mm Inches mm Inches
N 366 14.4 686 27.0
DE-05 = Ø340mm [13.4]
DE-10 = Ø640mm [25.2]
0.1m/s [4/s]
Included
Optional
Optional
Dirt: 5µm
Water: -20ºC@7 bar [940 ppm]
Oil: 0.1mg/m³
Non Lubricated
<70 dBA Leq
P 210 8.3 363 14.3
R 170 6.7 290 11.4
S 210 8.3 363 14.3
T 90 3.5 120 4.7
with cable carrier
Z - RAISED 1944 76.5 2857 112.5
U 230 9.1 165 6.5
V 162 6.4 227 8.9
X 500 19.7 1000 39.4
X - RAISED 1000 39.4 1955 77.0
Y 878 34.6 1313 51.7
Base elevator
Y - RAISED 1378 54.3 2268 89.3
Z 1694 66.7
SPECIFICATION
Stroke
Minimum air inlet pressure:
Maximum air inlet pressure:
Air inlet connection:
Maximum Load (including lid / lid support):
Maximum Load Distance:
Maximum drum diameter:
Maximum operating speed:
Up/Down controls:
Agitator controls:
Pump controls:
Recommended air quality ISO 8573.1 Class 3.3.2 #:
Noise Level @ 7 bar [100 psi]:
Earth connection resistance:
Weight:
Temperature range:
93.72380
77-3312 R3.0 (06/2025) 6/28 www.binks.com
EN
INSTALLATION
Dimensions in mm [inches]
RH Controls shown
BASE DETAIL
77-3312 R3.0 (06/2025) 7/28 www.binks.com
EN
INTENDED USE
The pneumatic elevator is designed for raising and lowering a drum/tank cover which has equipment mounted to
it, such as a pump, agitator or suction tube, generally for use in the painting industry.
This allows the drum/tank to be changed in the raised position. It is for professional trained users only.
PRIOR TO USE
WARNING
Attach the elevator base securely to a flat and level concrete floor, using 4 x M12 anchor bolts, each with an
applied tensile load of 6.1kN minimum.
For further fixing advice, please refer to the following documents:
BS 8539:2012 - Code of practice for the selection and installation of post-installed anchors in concrete and
masonry
BS EN 206:2013 - Concrete - specification, performance, production and conformity
EN 1992-4:2016 - Design of fastening for use in concrete
CEO Guidance Note - ETAs for anchors used in construction
Attach flexible hoses to all connections.
Connect a filtered and regulated air supply to the air connection.
Include a pressure relieving isolation valve.
Locate within 2m [80].
Operate the elevator at a low pressure for the first time and adjust speed of operation as specified.
Ensure maximum load and position are not exceeded.
Ensure the drum can be located in the correct position consistently, preferably with a location fixture.
The drum/tank cover position should be set with the elevator fully down.
Set the positon on the Ø32 mounting bar so there is a small clearance with the top of the drum/tank.
ATEX SPECIAL CONDITIONS FOR SAFE USE
WARNING
The elevator must be earthed at all times.
A resistance <1Ω when measuring with an ohm-meter at the earth point
Earth connection, Binks Part No. DEK-22
Metallic parts maintain earth continuity by either direct contact, toothed washers or earth cables.
After maintenance, ensure continuity is present to earth of <1 Ohm
77-3312 R3.0 (06/2025) 8/28 www.binks.com
EN
CONTROL PANEL
ITEM DESCRIPTION COMMENTS
1 Air supply
2
9 Agitator interlock valve
6 Up speed controller, check valve and pressure relief switch
7 Down speed controller and check valve
If fitted
10 Agitator on/off valve If fitted
11 Pump on/off valve If fitted
E To Agitator If fitted
F To Pump If fitted
8 Double acting cylinder
Manifold
3 Up/Down speed controller
4 Up pushbutton valve
5 Down pushbutton valve
PNEUMATIC DIAGRAM
77-3312 R3.0 (06/2025) 9/28 www.binks.com
EN
Toggle the valve '10' in the up position to turn air onto the agitator, valve '9' will only allow air to flow if the
elevator is in the down position.
The down position turns the air off.
Pump air control:
Toggle the valve '11' in the up position to turn air onto the agitator, the down position turns the air off.
WARNING
Valves '6' & '7' lock air pressure in the upper and lower sections of the cylinder.
Before undertaking any maintenance, drive the elevator down with pushbutton '5' and press pressure relief
switch on valve '6' until all air has been exhausted from the cylinder.
Up/Down position:
Initial speed -
The starting speed of up/down can be adjusted using valve '3' (located on inlet manifold), to increase or decrease
the speed.
See speed recommendation P6.
The remaining stroke speed is set using:
Up stroke - valve '6'
Down stroke - valve '7'.
OPERATION AND ADJUSTMENT - (REFER TO DIAGRAM ON P9)
Up/Down speed:
The unit should be in the fully down position when equipment mounted to it is in use.
To raise the elevator, press the top control panel pushbutton '4', the position can be stopped at any point.
To lower the elevator, press the bottom control panel pushbutton '5', the position can be stopped at any point.
NOTE
The valve '7' prevents downwards movement, unless it receives a signal from valve '5', preventing the elevator
dropping even if the hoses are disconnected accidentally.
CAUTION
The elevator should not be used as a permanent support.
Ensure personnel are clear of the elevator and operator has a clear view before operating.
Agitator air control:
77-3312 R3.0 (06/2025) 10/28 www.binks.com
EN
2 DEK-02 DEK-04 Cylinder cap - Complete kit
3 DEK-03 Mounting bar kit
4 DEK-10 DEK-11 Piston rod - Complete kit
5 DEK-14 DEK-15 Anti-rotation - Complete kit
SPARE PARTS
DE-05 DE-10
ITEM
PART No.
DESCRIPTION
1 DEK-01 DEK-05 Seal and bearing kit
77-3312 R3.0 (06/2025) 11/28 www.binks.com
EN
7 DEK-36 Agitator valve (pneumatic)
8 DEK-37 Agitator switch (electric)
9 DEK-21 Cover plates
10 DEK-22 Earth cable
1 DEK-30 Valve & fittings (up/green)
2 DEK-31 Valve & fittings (down/red)
3 DEK-32 Valve & fittings (agitator or pump)
4 DEK-33 Cylinder speed controllers
5 DEK-34 Inlet manifold & speed controller
6 DEK-20 Mounting brackets
SPARE PARTS
ITEM PART No. DESCRIPTION
Adjusting screw,
ensure smooth operation and
adjust accordingly.
77-3312 R3.0 (06/2025) 12/28 www.binks.com
EN
=
Grease
(AGMD-010)
= refer to figure
= Spanner or socket size
= Torque
Prior to carrying out any maintenance;
ensure the elevator is in the down position and all air is exhausted from the cylinder, prior to the air supply being
isolated and pressure relieved.
Follow the procedure below.
Isolate and exhaust air supply.
MAINTENANCE
Key - Maintenance symbols
=
Order for dis-assembly
(Reverse for assembly)
77-3312 R3.0 (06/2025) 13/28 www.binks.com
EN
MAINTENANCE
Agitator switch setting
77-3312 R3.0 (06/2025) 14/28 www.binks.com
EN
Monthly
- Check for air leaks
- check all parts are fixed securely
- ensure smooth operation and adjust accordingly.
6 Months
- Lubricate piston rod
- Lubricate anti-rotation rod
- Check for any excessive mechanical noise
12 Months
- Inspect bearings and seals, replace as required
- Lubricate all bearings and seals
- Check tightness of mounting bar fasteners
- Check rods for scoring
FAULT FINDING
SYMPTOM POSSIBLE CAUSE REMEDY
Up stroke speed
incorrect/erratic
a) Inlet manifold speed controller incorrectly
set
b) Cylinder top speed controller incorrectly
set
a) Adjust to set initial speed
b) Adjust to set remaining stroke
Down stroke speed
incorrect/erratic
Excessive movement
of elevator/items
a) Inlet manifold speed controller incorrectly
set
b) Cylinder bottom speed controller
incorrectly set
a) Loose fastenings
b) Worn bearings and/or seals
a) Adjust to set initial speed
b) Adjust to set remaining stroke
a) Tighten all fastenings
b) Replace worn parts
MAINTENANCE SCHEDULE
TYPICAL PERIOD RECOMMENDED OPERATION
77-3312 R3.0 (06/2025) 15/28 www.binks.com
EN
3 DEK-52 Lid 2.5kg [5.5 lbs]
Lid hole cap LDPE
Frame & Brackets
Steel - Powder Coated
Steel - Plated
LID ACCESSORIES - DE-05 (25/30L [5 gal])
ITEM PART No. DESCRIPTION WEIGHT
1 DEK-50 Lid & Support 7.2kg [16 lbs]
2 DEK-51 Lid Support 4.6kg [10 lbs]
MATERIALS OF CONSTRUCTION
Suction Tube
300 Series - Stainless Steel
Lids
Agitator shaft/impeller
Lid plates
Lid lock
Lid fasteners
77-3312 R3.0 (06/2025) 16/28 www.binks.com
EN
13 DEK-56 Lid 2.76kg [6.1 lbs]
8 DEK-82 3/4'' Suction Tube 0.95kg [2.1 lbs]
9 DEK-91 1/2'' Adapter Plate 0.15kg [0.33 lbs]
10 DEK-83 1/2'' Suction Tube 0.67kg [1.5 lbs]
11 DEK-92 Blank Plate 0.16kg [0.35 lbs]
12 DEK-55 Lid & Support 7.4kg [16.3 lbs]
3 DX200A Diaphragm Pump - Aluminium -
4 DEK-80 3/4'' Suction Tube 0.9kg [2 lbs]
6 DEK-81 1/2'' Suction Tube 0.6kg [1.3 lbs]
7 DEK-90 3/4'' Adapter Plate 0.15kg [0.33 lbs]
5 DX200S Diaphragm Pump - Stainless Steel -
LID ACCESSORIES - DE-05 (25/30L [5 gal])
ITEM PART NO. DESCRIPTION WEIGHT
1 0115-010337 Hole Cap 0.01kg [0.02 lbs]
41-3312X 1.82kg [4 lbs]
2
QS-PS40P12R 14.2kg [31.3 lbs]
Pneumatic Agitator
77-3312 R3.0 (06/2025) 17/28 www.binks.com
EN
LID ACCESSORIES - DE-05 (25/30L [5 gal])
Dimensions in mm [inches]
77-3312 R3.0 (06/2025) 18/28 www.binks.com
EN
3 DEK-67 Lid 7.5kg [16.5 lbs]
LID ACCESSORIES - DE-10 (205/210L [55 gal])
ITEM PART No. DESCRIPTION WEIGHT
1 DEK-65 Lid & Support 13.7kg [30.1 lbs]
2 DEK-66 Lid Support 6.3kg [13.9 lbs]
77-3312 R3.0 (06/2025) 19/28 www.binks.com
EN
13 DEK-68 Lid & Support 13.9kg [31 lbs]
14 DEK-69 Lid 7.7kg [17 lbs]
DEK-93 - must be earthed with a resistance of <1 Ohm
8 DEK-85 1/2'' Suction Tube 1.1kg [2.4 lbs]
9 DEK-87 1'' Suction Tube 2.8kg [6.2 lbs]
10 DEK-90 3/4'' Adapter Plate 0.15kg [0.33 lbs]
11 DEK-86 3/4'' Suction Tube 1.8kg [4 lbs]
12 DEK-92 Blank Plate 0.16kg [0.35 lbs]
CAUTION
QS-57X 5.6kg [12.3 lbs]
4 DEK-94 Mounting Plate 0.2kg [0.44 lbs]
5 DX200A Diaphragm Pump - Aluminium -
6 DEK-84 3/4'' Suction Tube 1.64kg [3.6 lbs]
7 DX200S Diaphragm Pump - Stainless Steel -
QS-PS80TP20S
3 Pneumatic Agitator
14.7kg [32.4 lbs]
LID ACCESSORIES - DE-10 (205/210L [55 gal])
ITEM PART No. DESCRIPTION WEIGHT
1 QS-XXXXXX Electric/Pneumatic Agitator -
2 DEK-93 Agitator Support 1.71kg [3.8 lbs]
77-3312 R3.0 (06/2025) 20/28 www.binks.com
EN
LID ACCESSORIES - DE-10 (205/210L [55 gal])
77-3312 R3.0 (06/2025) 21/28 www.binks.com
EN
LID ACCESSORIES - DE-10 (205/210L [55 gal])
Dimensions in mm [inches]
Dimension
G
See agitator manual for combinations and sizes.
H
77-3312 R3.0 (06/2025) 22/28 www.binks.com
EN
LID ACCESSORIES - DE-10 (205/210L [55 gal])
Dimensions in mm [inches]
77-3312 R3.0 (06/2025) 23/28 www.binks.com
EN
ACCESSORIES
ITEM PART No. DESCRIPTION WEIGHT
1
DEK-40 Ø8 x 5 (DE-05) Coil Hose
2
DEK-44 Bracket & Fittings (Single) 0.3kg [0.7 lbs]
0.4kg [0.9 lbs]
0.09kg [0.2 lbs]
DEK-41 Ø8 x 5 (DE-10) Coil Hose 0.09kg [0.2 lbs]
DEK-45 Bracket & Fittings (Double)
77-3312 R3.0 (06/2025) 24/28 www.binks.com
EN
ACCESSORIES
62 [2.44]
Bend radius 119 [4.7]
ITEM PART No. DESCRIPTION
Cable Carrier internal dimensions mm[inches]
DE-5 Cable Carrier 2.9kg [6.4 lbs]
DEK-47 DE-10 Cable Carrier 3.6kg [8 lbs]
DE-10 Mounting Tray 2.4kg [5.3 lbs]
2
DEK-48 DE-05 Mounting Tray 1.9kg [4.2 lbs]
DEK-49
WEIGHT
1
DEK-46
3 DEK-39 Mounting Bracket 1.3kg [2.9 lbs]
Width 50 [2]
Height
77-3312 R3.0 (06/2025) 25/28 www.binks.com
EN
ITEM PART No. DESCRIPTION WEIGHT
4kg [8.8 lbs]DE-5 Single Flexible Conduit AssemblyDEK-70
1
ACCESSORIES
DEK-72 4.7kg [10.4 lbs]DE-10 Single Flexible Conduit Assembly
2
6.6kg [14.6 lbs]DE-5 Double Flexible Conduit AssemblyDEK-71
8kg [17.7 lbs]DE-10 Double Flexible Conduit AssemblyDEK-73
0.9kg [2 lbs]
DE-5 Flexible Single Conduit and Fixing Kit (as DEK-
70 less brackets)
DEK-74Not Shown
1.6kg [3.5 lbs]
DE-10 Flexible Single Conduit and Fixing Kit (as DEK-
72 less brackets)
DEK-75Not Shown
77-3312 R3.0 (06/2025) 26/28 www.binks.com
EN
Tel: +81 45 785 6421
Australia Tel: +61 (0) 2 8525 7555
WARRANTY PAGE
WARRANTY POLICY
This product is covered by Binks materials and workmanship limited warranty.
The use of any parts or accessories, from a source other than Binks, will void all
warranties. Failure to reasonably follow any maintenance guidance provided, may
invalidate any warranty.
For specific warranty information please contact Binks.
For technical assistance or to locate an authorised distributor, contact one of our
international sales and customer support locations below.
REGION BINKS CONTACT
Americas Tel: 1-888-992-4657
Europe, Africa, Middle East Tel: +44 (0)1202 571 111
India marketingroa@binks.com
China Tel: +8621-3373 0108
Korea Tel: +82313663303
Japan
77-3312 R3.0 (06/2025) 27/28 www.binks.com
EN
Binks is a global leader in innovative finishing technologies. Binks reserves the right to modify
equipment specifications without prior notice.
Binks®, DeVilbiss®, and Ransburg® are registered trademarks of Binks US, LLC.
© 2025 Binks US, LLC. All rights reserved.
77-3312 R3.0 (06/2025) 28/28 www.binks.com
