- HAF 100 CFM Air Filter SB-6-146 [ English ]
®
SB-6-146-R5
HAF-502 100 CFM FILTER
HFRL-508 60 CFM FILTER-REGULATOR
www.binks.comSB-6-146-R5 (05/2025)
ENADDITIONAL RESOURCES
For additional information or copies of your service manual, please visit us online at:
binks.com/en/library
Or use this QR code with your mobile device:
HAF-502 100 CFM FILTER & HFRL-508 60 CFM FILTER-REGULATOR
Obey local or municipal regulations for product recycling and disposal.
binks.com/en/library
www.binks.com SB-6-146-R5 (05/2025)
EN 02. TABLE OF CONTENTS
i / ii
02 CONTENTS
03 SAFETY 1-2
03.1 SAFETY PRECAUTIONS AND HAZARDS..................................................................................................................1
03.2 ADDITIONAL SAFETY INFORMATION.......................................................................................................................1
04 PRODUCT OVERVIEW 3-6
04.1 SPECIFICATIONS........................................................................................................................................................3
04.2 INSTALLATION............................................................................................................................................................3
04.3 OPERATION.................................................................................................................................................................4
04.4 MAINTENANCE...........................................................................................................................................................4
04.5 PARTS LIST – HFRL-508.............................................................................................................................................5
04.6 PARTS LIST – HAF-502...............................................................................................................................................5
04.7 PARTS LIST – HAR-507..............................................................................................................................................6
04.8 REGULATOR MAINTENANCE....................................................................................................................................6
04.9 ACCESSORIES............................................................................................................................................................6
XX MANUAL REVISIONS 7
XX WARRANTY POLICY 11
www.binks.comSB-6-146-R5 (05/2025)
EN02. TABLE OF CONTENTS
ii / ii
This page intentionally left blank.
EN 03. SAFETY
www.binks.com 77-3049-R7 (08/2025)1 / 12
03 SAFETY
03.1 SAFETY PRECAUTIONS
Before the operation, maintenance, or servicing of this
Binks system; fully read and understand all technical and
safety literature for your product. This manual contains
information that is important for you to know and
understand.
This information relates to USER SAFETY and the
PREVENTION OF EQUIPMENT PROBLEMS.
To help you understand this information, we use
recognizable ANSI Z535 and ISO warning boxes and
symbols throughout this manual. Please obey these
safety sections.
WARNING
WARNING!: Indicates a hazardous situation that, if not
avoided, could result in death or severe injury.
CAUTION
Caution!: Indicates a hazardous situation that, if not
avoided, could result in minor or moderate injury, or
equipment damage.
NOTICE
Notice: Indicates information considered important but
not hazard related.
DANGER
DANGER!: Indicates a hazardous situation that, if not
avoided, will result in death or severe injury.
SAFETY
Safety: Indicates a type of safety instruction, or a
separate panel on a safety placard, where specific
safety-related instructions or procedures are described.
Careful study and continued use of this manual will
provide a better understanding of the equipment
functions and procedures.
This understanding will result in improved operation,
efficiency, and longer, trouble-free service with faster and
easier troubleshooting. If you need the necessary safety
literature for your specific system, contact your local
Binks representative or Binks directly.
WARNING
The hazards shown on the pages that follow can occur
during the normal use of this Binks equipment, but
not all listed hazards will be applicable to your product
model or equipment.
Repairs may only be performed by personnel
authorized by Binks.
WARNING
The user MUST read and be familiar with the Safety
Section in this manual and the safety literature therein
identified.
Only trained personnel can operate this equipment.
All personnel who operate, clean, or maintain this
equipment MUST fully read and understand this
manual! To operate and service the equipment, follow all
WARNINGS and safety requirements.
The user must be aware of and adhere to ALL local
building and fire codes and ordinances, as well as NFPA
33 AND EN 16985 SAFETY STANDARDS, LATEST
EDITION, or applicable country safety standards, before
the installation, operation, or servicing of this equipment.
NOTICE
This manual lists standard specifications and service
procedures. Differences can occur between this
literature and your equipment.
Differences in local or municipal codes, manufacturer
or plant requirements, material delivery requirements,
and more can make variations unpreventable. To
find these differences, compare this manual to your
system installation drawings and other applicable Binks
equipment manuals.
03.2 ADDITIONAL SAFETY INFORMATION
Observe all local or municipal safety measures and
wear approved protective equipment when servicing this
equipment. Clean all spilled chemicals and materials
and do all work in a clean and organized environment to
prevent personal injury and equipment damage.
EN03. SAFETY
www.binks.com77-3049-R7 (08/2025) 2 / 12
This page intentionally left blank.
EN 04. PRODUCT OVERVIEW
www.binks.com SB-6-146-R5 (05/2025)3 / 12
04 PRODUCT OVERVIEW
HAF-502 100 CFM FILTER
HFRL-508 60 CFM FILTER-REGULATOR
This 100 CFM filter (Model HAF-502) is designed to
remove dirt, pipe scale and most liquid aerosol. It
includes a 5 micron filter element. A model with 60 CFM
air regulator is also available (Model HFRL-508).
WARNING
Risk of personal injury.
Risk of property damage.
Except as otherwise specified by the manufacturer,
this product is specifically designed for compressed air
service and use with any other fluid (liquid or gas) is
a misapplication. For example, use with or injection of
certain hazardous gases in the system (such as oxygen
or liquid petroleum gas) could be harmful to the unit or
result in a combustible condition that may cause fire
or explosion. Manufacturer’s warranties are void in the
event of misapplication and manufacturer assumes no
responsibility for any resulting loss.
04.1 SPECIFICATIONS
AIR FILTER
Air Inlet 1/2 NPT(F)
Air Outlet 1/2 NPT(F)
Air Flow Capacity 100 CFM (60 CFM with air
regulator on Model HFRL-508)
Maximum Temp. 150° F (65.6° C)
Max. Inlet Pressure 150 psig (10.3 bar)
Max. Operating Pressure 150 psig (10.3 bar)
AIR CONNECTIONS MODEL HFRL-508
Regulated Non-Regulated
(1) 1/4 NPS(M) (1) 1/4 NPS(M)
(1) Plugged Port
04.2 INSTALLATION
WARNING
Risk of injury. Release all air pressure from system
before servicing system. Do not place unit in service
without metal bowl guard installed. Plastic bowl
units are sold only with metal bowl guards. To
minimize the danger of flying fragments in the event
of plastic bowl failure, guard must not be removed.
If the unit is in service without the metal bowl guard
installed, manufacturer's warranties are void and the
manufacturer assumes no responsibility for a resulting
loss. If unit has been in service and does not have a
metal bowl guard, order one and install before placing
back in service.
CAUTION
Certain solvents, paints and chemicals may attack
plastic bowl and can cause bowl failure. Do not use
near these materials.
1. �Be sure to read all Warnings and Cautions in this
manual and on the unit before installation or using this
equipment.
2. �Install filter as close as possible to point where air is
being used. Install main air shut-off valve and standard
pipe union (supplied by user) upstream of filter to allow
maintenance to unit.
3. �Install unit with air flow through filter in direction of
arrow on top of unit.
4. �Minimum 1/2 piping is recommended. Avoid using
fittings, couplings, etc. that restrict air flow.
5. �A 1/2 street elbow will be needed to allow vertical pipe
installation. Mount filter in a vertical position.
6. �Do not install filter in an application where the pressure
drop will exceed 20 psi. For example, a quick opening
valve located upstream from the filter could cause a
momentary pressure drop in excess of 20 psi.
7. �Install T handle into regulator (Model HFRL-508).
8. �Maximum inlet pressure and operating temperature is:
150 PSIG (10.3 bar) and 150° F (65.6° C).
9. �A 6' length of vinyl tubing is shipped loose with the
unit. Slide over automatic drain which protrudes from
bottom of bowl. Place other end of vinyl tubing into
appropriate receptacle (i.e. below booth grating, can,
EN04. PRODUCT OVERVIEW
www.binks.comSB-6-146-R5 (05/2025) 4 / 12
etc.). Prevent vinyl tubing from becoming kinked which
would prevent free movement of liquids discharged
from the automatic drain.
10. �An optional manual drain (HAF-11) is supplied loose
in the carton (see item 10, HAF-502 Parts List). If
desired, this can be installed in place of the automatic
drain.
04.3 OPERATION
After unit is installed and ready to use:
1. �Attach air hose(s) to outlet ball valve(s), selecting
regulated and/or non-regulation according to the
application.
2. �Open main shut-off valve upstream of filter.
3. �Main line air pressure is monitored by the top air
gauge.
4. �Adjust regulator to desired setting by turning T
handle in or out.
5. �Open ball valve(s) to supply air to spray gun or tool
being used. With air flowing, readjust air pressure at
regulator if necessary.
6. �After use, shut off ball valve(s) and bleed off residual
air in hose(s).
04.4 MAINTENANCE
CAUTION
Certain solvents, paints and chemicals may attack
plastic bowl and can cause bowl failure. Do not use
near these materials. When bowl becomes dirty, wipe
only with a clean, dry cloth. Immediately replace any
crazed, cracked, damaged or deteriorated plastic bowl
with a new plastic bowl. Reinstall metal bowl guard.
1. �If bowl is equipped with manual drain, drain bowl at
least once per shift. Units with automatic drain will
drain automatically.
2. �Before performing maintenance on unit, close main
shut-off valve located upstream of filter. Bleed off
residual air in unit.
3. �To open filter, press button located on clamp ring and
rotate ring either clockwise or counterclockwise. The
metal bowl guard and plastic bowl can then be
removed from the filter head.
4. �Remove the filter element by loosening the baffle
counterclockwise. Clean or replace the filter element.
The element can be cleaned by blowing off with a
duster gun (clean from inside out). Frequency of
element cleaning/replacement will depend upon air
quality, air usage, and condition of the air piping. It is
recommended to check and clean/replace the element
every 3-6 months.
5. �Inspect o-ring (2) for damage. Replace if necessary.
6. �Inspect plastic bowl for signs of damage such as
cracks, crazing or deterioration. Replace if necessary.
See Caution at beginning of Maintenance section.
NOTICE
Do not wash plastic bowl with the automatic drain
installed. Water can get into the float mechanism,
causing the drain to malfunction. Remove the automatic
drain before cleaning the plastic bowl with soap and
water (no solvents).
WARNING
Do not place unit in service without metal bowl guard
installed.
7. �Before placing unit back into service, make sure
plastic bowl and metal bowl guard are properly
installed and securely locked in place.
8. �Confirm automatic drain operates properly after unit is
in operation. Replace if necessary.
EN 04. PRODUCT OVERVIEW
www.binks.com SB-6-146-R5 (05/2025)5 / 12
ITEM
NO. PART NO. DESCRIPTION QTY.
1 HAF-502 Air Filter, 100 CFM
(See HAF-502 Parts List) 1
2 HAF-21 Cross Manifold 1
3 GA-288 Air Gauge, 0-160 psi (main line) 1
4 83-2727 Air Gauge, 0-100 psi (regulated) 1
5 HAR-507 Air Regulator (See Fig. 3) 1
6 — 1/4 Street Elbow, 90° 1
7 VA-542 Ball Valve 2
04.5 PARTS LIST – HFRL-508
HFRL-508 FILTER/REGULATOR (60 CFM)
1
5
43
2
7
6
HAF-502 FILTER (100 CFM)
1
6
5
4
3
2
8
7
10
(Optional)
9
ITEM
NO. PART NO. DESCRIPTION QTY.
1 — Cover 1
2 — O-Ring 1
3 HAF-26 Baffle Kit 1
4 HAF-6 Filter and O-Ring Kit 1
5 HAF-18 Automatic Drain (Std.) 1
6 HAF-8 Plastic Bowl 1
7 HAF-19 Metal Bowl Guard 1
8 HAF-409 Clamp Ring 1
9 — 1/2 x 3/8 Vinyl Tubing, 6 ft. 1
10 HAF-11 Manual Drain
(Optional, shipped loose) 1
04.6 PARTS LIST – HAF-502
EN04. PRODUCT OVERVIEW
www.binks.comSB-6-146-R5 (05/2025) 6 / 12
HAR-507 REGULATOR ASSEMBLY, 60 CFM
ITEM
NO.
PART
NO. DESCRIPTION QTY.
1 — #10-32 x 9/16 Fillister Hd. Screw 6
2 — Cover 1
3 — Spring Button 1
4 — Diaphragm Spring 1
5 — Body 1
6 — Pipe Plug 1/4 NPT(M) 1
7 — Bottom Plug 1
8 KK-4977 Repair Kit (includes Items 9 thru 14) 1
9 — Diaphragm Assembly 1
10 — O-Ring 1
11 — Valve 1
12 — O-Ring 1
13 — Spring 1
14 — O-Ring 1
04.7 PARTS LIST – HAR-507
04.8 REGULATOR MAINTENANCE
1. �Occasionally remove bottom plug (7) and clean valve
seat (11) and body. Clean parts with denatured
alcohol, wipe off seat and blow out body with
compressed air.
2. �To disassemble regulator, remove screws, bonnet,
spring and spring button. Diaphragm assembly can
now be removed.
3. �Check all o-rings for signs of damage. Replace if
necessary.
4. �Reassemble parts. Center stem of valve in hole of
regulator body. Screw bottom plug into body.
7
14
13
1
2
3
4
9
10
11
12
6
5
8
A
NOTICE
Erratic operation or loss of regulation is usually due
to dirt in the valve area and cleaning is necessary. If
cleaning does not correct the problem, replace the items
included in Repair Kit KK-4977. If unit leaks air at A ,
install Repair Kit KK-4977.
04.9 ACCESSORIES
HAF-407 BRACKET ASSEMBLY KIT
Used with HAF-502 and HFRL-508.
EN 05. MANUAL REVISIONS
www.binks.com SB-6-146-R5 (05/2025)7 / 12
MANUAL CHANGE SUMMARY
Date Description Version
08/05/2025 Rebranded to Binks R5
EN05. MANUAL REVISIONS
www.binks.comSB-6-146-R5 (05/2025) 8 / 12
This page intentionally left blank.
EN 05. MANUAL REVISIONS
www.binks.com SB-6-146-R5 (05/2025)9 / 12
This page intentionally left blank.
EN05. MANUAL REVISIONS
www.binks.comSB-6-146-R5 (05/2025) 10 / 12
This page intentionally left blank.
EN 06. WARRANTY
WARRANTY POLICY
This product is covered by Binks’ materials and workmanship limited warranty.
The use of parts or accessories from sources other than Binks will void all warranties. Failure to follow reasonable
maintenance guidance provided can invalidate the warranty.
For specific warranty information, please contact Binks.
For technical assistance or to locate an authorized distributor, contact one of our international sales
and customer support locations listed below.
www.binks.com SB-6-146-R5 (05/2025)11 / 12
WARRANTY PAGE
REGION BINKS CONTACT
Americas Tel: 1-800-992-4657
Europe, Africa, Middle East Tel: +4401202571111
India marketingroa@binks.com
China Tel: +862133730108
Korea Tel: +82313663303
Japan Tel: +81457856421
Australia Tel: +61085257555
EN
Binks is a global leader in innovative finishing technologies.
Binks reserves the right to modify equipment specifications without prior notice.
Binks®, DeVilbiss® and Ransburg® are registered trademarks of Binks US, LLC.
©2025 Binks US, LLC. All rights reserved.
®
