Resource Library
QuickHose Connector Replacement Kit Manual 347555
- QuickHose Connector Replacement Kit Manual 347555 [ English ]
347555
®
CONNECTOR REPLACEMENT KIT
FULL HOSE: 347556
PARTS/TOOLS:
Item Description Qty
a POWER CONNECTOR, HOSE 8
b FERRULE, 16 AWG 54
c VINYL INDICATOR TAPE, RED 6(IN)
d VINYL INDICATOR TAPE, BLUE 6(IN)
e SCREWDRIVER, #1 1
f WIRE STRIPPER/CUTTER (NOT INCLUDED) 1
g PLIERS (NOT INCLUDED) 1
h 3MM ALLEN WRENCH (FOR CLAMPS) 1
EN
www.binks.com347555 REV C (05/2025) © Binks US, LLC. All Rights Reserved
1. Turn off power to equipment.
2. Remove any necessary hose wrap and clamps to
expose connector.
3. Identify connector in need of replacement.
4. Mark each cable with appropriate colored tape (c
or d) on cable, 2 from back of connector (RED—A,
BLUE—B). Fig. 1.
5. Remove old connector by cutting cable directly
behind connector. (Fig. 2)
6. Strip back outer cable jacket 0.75 to expose (3X)
conductors. Be careful not to cut individual conductor
insulation. (Use Fig. 3 for measurement reference)
7. Using 16AWG wire stripping tool (f), strip back each
conductor 0.30 (between 1/4 and 3/8). Use Fig. 3.
NOTE: Be careful not to nick or cut copper strands
when stripping wire. If any strands are accidentally
cut, repeat from step 4.
8. Install one ferrule (b) on each conductor, and pinch
metal portion of ferrule flat with pliers (g). End of
copper strands should be at or beyond end of ferrule.
(Fig. 4)
NOTE: Crimp ferrule from end (not side) and ensure
that ferrule insulation is completely covering exposed
copper wires before crimping.
9. Trim off excess wire strands that stick beyond end of
ferrule (Fig. 5)
ELECTRICAL SHOCK HAZARD: Disconnect
all power sources before accessing any
electrical connections in the Control Module,
Fluid Modules, or hoses. Equipment must be
serviced by trained personnel only.
FIRE AND EXPLOSION HAZARD: Improper
equipment grounding, poor ventilation, open
flame or sparks can cause a hazardous
condition and result in fire or explosion and
serious injury.
NEVER MODIFY THE EQUIPMENT:
Do not modify the equipment unless the
manufacturer provides written approval.
WARNING
Read the following warnings before performing any
maintenance
Fig. 1
2.00
(cord)
Fig.2
CUT
USE IMAGE FOR
MEASUREMENT
0.75
0.30
Fig.3
Fig.4
(b)
Fig.5
CUT FLUSH
EN
www.binks.com 347555 REV C (05/2025)© Binks US, LLC. All Rights Reserved
10. Slide (1) connector nut, (1) sealing gasket, and (1)
housing onto cable . (Fig. 6)
11. Install conductors (with ferrules installed) into main
connector body, and tighten screws using screwdriver
(e). (Fig. 7,8)
NOTE: Install conductors completely into housing
before tightening.
NOTE: See Figure 8 for correct location of each
conductor into connector body. DO NOT insert
conductors into wrong location on the connector
body!
12. Screw connector housing to connector body and
tighten until housing bottoms out. (Fig. 9)
13. Insert gasket into connector housing and tighten nut
over housing. (Fig. 10)
NOTE: Nut should be tightened until nut bottoms out
on housing.
NOTE: Make sure gasket under connector nut grips
outer cable jacket.
NOTE: Make sure conductors match (Ground wire,
One-1 [Black], Two-2 [Black]) on both ends of the
same connector.
14. If necessary, repeat steps 4-13 for other end of
connector.
NOTE: Make sure A cable (red heat shrink/tape) is
connected to A cable (red heat shrink/tape), and B
cable (blue heat shrink/ tape) is connected to B cable
(blue heat shrink/tape)
15. Nest connector in hose bundle, eliminate any tension
in cable, and re-cover with hose wrap.
16. Repeat with rest of hose power connections.
Nut
Gasket
Housing
Fig.6
Fig. 7
ONE-1 (Black)
Wire (L terminal)
Fig. 8Green/Yellow
Wire (G terminal)
Two-2 (Black)
Wire (N terminal)
Fig. 9
Fig. 10
Fig. 11
Match cables per side
WARRANTY POLICY
This product is covered by Binks’ materials and workmanship limited warranty.
The use of parts or accessories from sources other than Binks will void all
warranties. Failure to follow reasonable maintenance guidance provided can
invalidate the warranty.
For specific warranty information, please contact Binks.
For technical assistance or to locate an authorized distributor, contact one of our
international sales and customer support locations listed below.
REGION BINKS CONTACT
Americas Tel: 1-800-992-4657
Europe, Africa, Middle East Tel: +4401202571111
India marketingroa@binks.com
China Tel: +862133730108
Korea Tel: +82313663303
Japan Tel: +81457856421
Australia Tel: +61085257555
WARRANTY PAGE
Binks is a global leader in innovative finishing technologies.
Binks reserves the right to modify equipment specifications without prior notice.
Binks®, DeVilbiss® and Ransburg® are registered trademarks of Binks US, LLC.
