- Binks DX70 Pump Packages Service Manual - 77-3201 EN [ English ]
77-3201
DX70
Pump Packages
Patent US 9447780
EN
ADDITIONAL RESOURCES
For additional information or copies of your service manual, please visit us online at:
binks.com/en/library
Or use this QR code with your mobile device:
XXXXXXXX
Insert
QR
code
Obey local or municipal regulations for product recycling and disposal.
IMPORTANT! DO NOT DESTROY
It is the Customer's responsibility to have all operators and service personnel read and
understand this manual.
Contact your local Binks representative for additional copies of this manual.
READ ALL INSTRUCTIONS BEFORE OPERATING THIS PRODUCT
77-3201 R4 (06/2025) 2/20 www.binks.com
EN
Product Description / Object of Declaration: Diaphragm Pumps - DX70, DX200, DX200-3 Bare pump and
packages
This Product is designed for use with: Solvent & Waterbased Materials
Suitable for use in hazardous area: Zone 1/Zone 2
Protection Level: II 2 G Ex h IIB T4 Gb
Notified body details and role: Element Materials Technology Rotterdam B.V. (2812)
Lodging of ATEX Technical file
This Declaration of Conformity / Incorporation is issued
under the sole responsibility of the manufacturer:
Binks U.K. Limited,
Ringwood Road,
Bournemouth, BH11 9LH. UK
Representative authorised to compile the technical file President @. Binks France SAS
5 Place Pierre Semard, 94130 Nogent sur Marne , Paris, France
EU Declaration of Conformity
This Declaration of Conformity / Incorporation is issued under the sole responsibility of the
manufacturer:
Machinery Directive 2006/42/EC
ATEX Directive 2014/34/EU
by complying with the following statutory documents and harmonised standards:
EN ISO 12100:2010 Safety of Machinery - General Principles for Design
EN 12621:2006+2010 Machinery for the supply and circulation of coating materials under pressure - Safety requirements
EN ISO 80079-36:2016 Explosive Atmospheres- Part 36:Non Electrical equipment for explosive atmospheres-Basic methods
and requirements.
EN ISO 80079-37:2016 Explosive Atmospheres- Part 37: Non Electrical equipment for explosive atmospheres - protection by
methods c, b and k.
EN 1127-1:2019 Explosive atmospheres - Explosion prevention - Basic concepts
Providing all conditions of safe use / installation stated within the product manuals have been complied with and also installed in accordance
with any applicable local codes of practice.
Signed for and on behalf of Binks
U.K. Ltd:
Executive President: Engineering and
Operations, Shoreview, MN, 55126. USA
F. A. Sutter
Document Part No.
. 22-04-25
77-3201 R4 (06/2025) 3/20 www.binks.com
EN
This Declaration of Conformity / Incorporation is issued under the sole responsibility of the
manufacturer:
Supply of Machinery (Safety) Regulations 2008
Equipment and Protective Systems Intended for use in Potentially Explosive Atmospheres Regulations 2016
by complying with the following statutory documents and designated standards:
BS EN ISO 12100:2010 Safety of Machinery - General Principles for Design
BS EN 12621:2006+2010 Machinery for the supply and circulation of coating materials under pressure - Safety requirements
BS EN ISO 80079-36:2016 Explosive Atmospheres- Part 36:Non Electrical equipment for explosive atmospheres-Basic
methods and requirements.
BS EN ISO 80079-37:2016 Explosive Atmospheres- Part 37: Non Electrical equipment for explosive atmospheres - protection
by methods c, b and k.
BS EN 1127-1:2019 Explosive atmospheres - Explosion prevention - Basic concepts
Providing all conditions of safe use / installation stated within the product manuals have been complied with and also installed in accordance
with any applicable local codes of practice.
Signed for and on behalf of Binks
U.K. Ltd:
Executive President: Engineering and
Operations, Shoreview, MN, 55126. USA
F. A. Sutter
Document Part No.
. 22-04-25
Approved body details and role: Element Materials Technology Warwick Ltd. UK. (0891)
Lodging of UKEX Technical file
This Declaration of Conformity / Incorporation is issued
under the sole responsibility of the manufacturer:
Binks U.K. Limited,
Ringwood Road,
Bournemouth, BH11 9LH. UK
UKCA Declaration of Conformity
Product Description / Object of Declaration: Diaphragm Pumps - DX70, DX200, DX200-3 Bare pump and
packages
This Product is designed for use with: Solvent & Waterbased Materials
Suitable for use in hazardous area: Zone 1/Zone 2
Protection Level: II 2 G Ex h IIB T4 Gb
77-3201 R4 (06/2025) 4/20 www.binks.com
EN
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PROVIDE THIS INFORMATION TO THE
OPERATOR OF THE EQUIPMENT.
INSPECT THE EQUIPMENT DAILY. Inspect the equipment for worn
or broken parts on a daily basis. Do not operate the equipment if
you are uncertain about its condition.
OPERATOR TRAINING. All personnel
must be trained before operating
finishing equipment.
EQUIPMENT MISUSE HAZARD. Equipment misuse can cause the
equipment to rupture, malfunction or start unexpectedly and result
in serious injury. PACEMAKER WARNING. You are in the
presence of magnetic fields which may
interfere with the operation of certain
pacemakers.HIGH PRESSURE CONSIDERATION. High pressure can cause serious
injury. Relieve all pressure before servicing. Spray from the gun,
hose leaks or ruptured components can inject fluid into your body
and cause extremely serious injury.
KEEP EQUIPMENT GUARDS IN PLACE.
Do not operate the equipment if the
safety devices have been removed.
STATIC CHARGE. Fluid may develop a static charge that must be
dissipated through proper grounding of the equipment, objects to be
sprayed and alll other electrically conductive objects in the
dispensing area. Improper grounding or sparks can cause a
hazardous condition and result in fire, explosion or electric shock and
other serious injury.
NEVER MODIFY THE EQUIPMENT. Do
not modify the equipment unless the
manufacturer provides written
approval.
PROP 65 WARNING. WARNING: This product contains chemicals
known to the state of California to cause cancer and birth defects or
other reproductive harm.
PINCH POINT HAZARD. Moving parts
can crush and cut. Pinch points are
any areas where ther are moving
parts.
Read the following warnings before using this equipment.
READ THE MANUAL. Before operating finishing equipment, read and
understand all safety, operation and maintenance information
provided in the operation manual.
AUTOMATIC EQUIPMENT. Automatic
equipment may start suddenly without
warning.
WEAR SAFETY GLASSES. Failure to wear safety glasses with side
shields could result in serious eye injury or blindness.
PROJECTILE HAZARD. You may be
injured by venting liquids or gases
that are released under pressure, or
flying debris.
DE-ENERGIZE, DE-PRESSURISE, DISCONNECT AND LOCK OUT ALL
POWER SOURCES DURING MAINTENANCE. Failure to de-energize,
disconnect and lock out all power supplies before performing
equipment maintenance could cause serious injury or death. KNOW WHERE AND HOW TO SHUT
OFF THE EQUIPMENT IN CASE OF AN
EMERGENCY.
NOISE LEVELS. The A-weighted sound level of pumping and spray
equipment may exceed 85 dB(A) depending on equipment settings.
Actual noise levels are available on request. It is recommended that
ear protection is worn at all times while equipment is in use.
PRESSURE RELIEF PROCEDURE.
Always follow the pressure relief
procedure in the equipment
instruction manual.
In this part sheet, the words WARNING, CAUTION and NOTE are used to emphasize important safety information as
follows:
WARNING CAUTION NOTE
Hazards or unsafe practices which could result in
severe personal injury, death or substantial property
damage.
Hazards or unsafe practices which could result in
minor personal injury, product or property
damage
Important installation, operation or maintenance
information.
WARNING
77-3201 R4 (06/2025) 5/20 www.binks.com
EN
F2Air controls
Tripod gravity mount Kit
-
8 0114-011798
Item
-
F1
F4
DX Tripod assembly
4m Grounding cable
Tripod Mounted Pumps
7 DXK-100
Bare pump
Screw kit
DXA-S25ME15
DXA-F10ME100 Filter assembly F3
F5
-
Part No. Description See figure
DXA-T
Suction hose
DXA-AC#
4 DXA-TG
5
6 DX70#-##
1
2
3
77-3201 R4 (06/2025) 6/20 www.binks.com
EN
DXK-101
1 DVX-101
-
5
10
2
DXA-CG
F3
DXA-S25ME15
F6
DXA-F10ME100
4
DXA-WG Wall gravity feed kit
Cart
Bare pump
7
8
Filter assembly
Screw kit
F2DXA-AC#
-
Cart gravity feed kit
0115-010186
0114-011798
3
4m Grounding cable
Cart & Wall Mounted Pumps
-
6 DX70#-##
-
DXK-100
Screw kit
-
Item
Wall bracket
Air controls
-
Part No. Description See figure
Suction hose F5
9
77-3201 R4 (06/2025) 7/20 www.binks.com
EN
41-3312-S
7 -
-0115-010337
Pail Mounted Pumps
Blanking Plug
DXA-AF
Filter assembly F3
6
8
Pail Lid
DXK-107 -
-
Part No.
Air controls F2
5 DX70#-##
0114-011798
4
4m Grounding cable
3
-
-Agitator
11
9
10
Item
-
Agitator air supply
DXA-P25ME15
1 DVX-116
DXA-F10ME100
Pail Suction Tube
2 DXA-AC#
Bare pump
Screw kit
F7
-
Description See figure
Seal - pack of 4
DXK-100
77-3201 R4 (06/2025) 8/20 www.binks.com
EN
F1
Fixing kitDXK-102
1 0115-010210
DXA-T
Reference figures
Tripod leg
Item Part No. Description
2
77-3201 R4 (06/2025) 9/20 www.binks.com
EN
F2
F2
F2
Pressure gauge
DXA-AC1
S-1817
1 GA-382-P
Item Part No.
3 MPV-10
Ø4 [5/3''] Air tube
DXA-AC3
DXA-AC2
QD stem 1/4 female
2
Description
77-3201 R4 (06/2025) 10/20 www.binks.com
EN
F3
1. Filters that are supplied as part of a pump package will
have the blanking plugs fixed in place with Loctite sealant to
allow for full assembly testing.
Removal / repositioning of the blanking plugs may lead to
damage to the filter which could void any warranty
2. Filters can be purchased with plugs not fixed, as spares.
Refer to Service Information Sheet 77-3334 for details
2
Filter 150 µm/100 mesh
3/8'' x 1/4'' Universal (BSPP/NPSM) nipple
VS-58
1 0114-016021
Filter feed hose
DXA-F10ME100
3 DVX-100
VS-58-60
Part No. Description
IMPORTANT NOTE
Item
Filter 250 µm/60 mesh
77-3201 R4 (06/2025) 11/20 www.binks.com
EN
F4
Filter
00-00-00021481 Tension ring
DXA-TG
Item Part No. Description
00-00-0002147
3 ZZ-2571
2
6L [1.6 US Gal] Hopper
Suction hose
PTFE Seal
5 Adapter
Clamp kitDXK-103
DVX-125
6
DVX-93
7
4 ZZ-2587
77-3201 R4 (06/2025) 12/20 www.binks.com
EN
F5
DXA-S25ME15
Item Description
1
2 DXK-104
DVX-893
Suction hose
Seal - pack of 4
Strainer 1300µm/15 mesh
DVX-86
Part No.
77-3201 R4 (06/2025) 13/20 www.binks.com
EN
F6
F7
DXA-P25ME15
DXA-CG & WG
Item Part No. Description
Tension ring
Fixings
Locknut
Adapter
Suction hose
3
DVX-89
DXK-101
6 DVX-99
7
Part No. Description
Strainer
Item
ZZ-2571
PTFE Seal
6L [1.6 US Gal] Hopper
00-00-0002148
DVX-125
DVX-96
8
1
4 ZZ-2587
5
Strainer 1300µm/15 mesh1
2 00-00-0002147
77-3201 R4 (06/2025) 14/20 www.binks.com
EN
DXA-DVG
Accessories
Dump valve kit for tripod & pail
Dump valve kit for gravity feed
Dump valve kit for wall/cart
DXA-DVT
DXA-DVW
77-3201 R4 (06/2025) 15/20 www.binks.com
EN
DXA-AF
Accessories
Agitator air supply
Fluid regulator maximum pressure supply
DXA-RP
77-3201 R4 (06/2025) 16/20 www.binks.com
EN
R
N
-
1
2
3 A
C -
W F
T
P
TRIPOD
G
Package - Part numbers
OPTIONS
3 REGULATORS
2 REGULATORS
1 REGULATOR
DX70 R 3 - C F G
FLUID REGULATOR
NO FLUID REGULATOR
NO OPTION
AGITATOR
NO FILTER
FILTER
PAIL
REGULATOR TYPE
MOUNTING TYPE
WALL
CART
FILTER
GRAVITY FEED
AIR REGULATORS
77-3201 R4 (06/2025) 17/20 www.binks.com
EN
NOTES
77-3201 R4 (06/2025) 18/20 www.binks.com
EN
WARRANTY POLICY
This product is covered by Binks materials and workmanship limited warranty.
The use of any parts or accessories, from a source other than Binks, will void all
warranties. Failure to reasonably follow any maintenance guidance provided, may
invalidate any warranty.
For specific warranty information please contact Binks.
For technical assistance or to locate an authorised distributor, contact one of our
international sales and customer support locations below.
REGION BINKS CONTACT
Americas Tel: 1-888-992-4657
Europe, Africa, Middle East Tel: +44 (0)1202 571 111
India marketingroa@binks.com
China Tel: +8621-3373 0108
Korea Tel: +82313663303
Japan Tel: +81 45 785 6421
Australia Tel: +61 (0) 2 8525 7555
WARRANTY PAGE
77-3201 R4 (06/2025) 19/20 www.binks.com
EN
Binks is a global leader in innovative finishing technologies. Binks reserves the right to modify
equipment specifications without prior notice.
Binks®, DeVilbiss®, and Ransburg® are registered trademarks of Binks US, LLC.
© 2025 Binks US, LLC. All rights reserved.
77-3201 R4 (06/2025) 20/20 www.binks.com
