- Binks i-Flow SE 70CC E-DOSER 25-0634 Service Manual [ English ]
25-0634_EN R6
I-FLOW SE 70CC E-DOSER
®
www.binks.com25-0634_EN R6 (01/2025)
ENADDITIONAL RESOURCES
For additional information or copies of your service manual, please visit us online at:
binks.com/en/library
Obey local or municipal regulations for product recycling and disposal.
www.binks.com 25-0634_EN R6 (01/2025)
EN 02 TABLE OF CONTENTS
i / ii
02 CONTENTS
03 SAFETY 3
SAFETY PRECAUTIONS..........................................................................................................................................3
ADDITIONAL SAFETY INFORMATION..................................................................................................................10
04 INTRODUCTION 11
SYSTEM OVERVIEW..............................................................................................................................................11
I-FLOW SE CONTROLLER SPECIFICATIONS.....................................................................................................12
SHOT METER SPECIFICATIONS..........................................................................................................................15
SYSTEM INTERFACE..............................................................................................................................................18
INSTALLATION.........................................................................................................................................................19
05 SHOT METER ASSEMBLY 21
ASSEMBLY VIEWS..................................................................................................................................................21
PARTS LIST..............................................................................................................................................................21
REBUILD KITS.........................................................................................................................................................22
SPECIAL TOOLS......................................................................................................................................................23
LOCK-OUT / TAG-OUT............................................................................................................................................25
TOOLS REQUIRED..................................................................................................................................................27
MATERIAL REQUIRED............................................................................................................................................27
DISASSEMBLY PROCEDURES.............................................................................................................................27
REFILL / DISPENSE VALVES.................................................................................................................................56
06 SHOT METER BODY 58
ASSEMBLY VIEWS..................................................................................................................................................58
PARTS LIST..............................................................................................................................................................59
TOOLS REQUIRED..................................................................................................................................................60
MATERIAL REQUIRED............................................................................................................................................60
DISASSEMBLY PROCEDURES.............................................................................................................................60
ASSEMBLY PROCEDURES....................................................................................................................................62
07 REFILL 64
08 DISPENSE VALVE 65
09 LUBRICATOR 66
10 PURGE STAND 67
11 MAINTENANCE 68
MAINTENANCE SCHEDULE..................................................................................................................................68
TROUBLE SHOOTING GUIDE...............................................................................................................................69
12 MANUAL REVISIONS 73
13 WARRANTY 75
www.binks.com25-0634_EN R6 (01/2025)
EN02 TABLE OF CONTENTS
ii / ii
This page intentionally left blank.
EN 03 SAFETY
www.binks.com 25-0634_EN R6 (01/2025) 3 / 76
03 SAFETY
SAFETY PRECAUTIONS
Before the operation, maintenance, or servicing of this
Binks system; fully read and understand all technical
and safety literature for your product. This manual
contains information that is important for you to know and
understand.
This information relates to USER SAFETY and the
PREVENTION OF EQUIPMENT PROBLEMS.
To help you understand this information, we use
recognizable ANSI Z535 and ISO warning boxes and
symbols throughout this manual. Please obey these
safety sections.
Careful study and continued use of this manual will
provide a better understanding of the equipment functions
and procedures.
This understanding will result in improved operation,
efficiency, and longer, trouble-free service with faster and
easier troubleshooting. If you need the necessary safety
literature for your specific system, contact your local Binks
representative or Binks directly.
WARNING
WARNING!: Indicates a hazardous situation that, if not
avoided, could result in death or severe injury.
CAUTION
Caution!: Indicates a hazardous situation that, if not
avoided, could result in minor or moderate injury, or
equipment damage.
NOTICE
Notice: Indicates information considered important but
not hazard related.
DANGER
DANGER!: Indicates a hazardous situation that, if not
avoided, will result in death or severe injury.
SAFETY
Safety: Indicates a type of safety instruction, or a
separate panel on a safety, where specific safety-
related instructions or procedures are described.
WARNING
The hazards shown on the pages that follow can occur
during the normal use of this Binks equipment, but
not all listed hazards will be applicable to your product
model or equipment.
Repairs may only be performed by personnel
authorized by Binks.
WARNING
The user MUST read and be familiar with the Safety
Section in this manual and the safety literature therein
identified.
Only trained personnel can operate this equipment.
All personnel who operate, clean, or maintain this
equipment MUST fully read and understand this
manual! To operate and service the equipment, follow all
WARNINGS and safety requirements.
The user must be aware of and adhere to ALL local
building and fire codes and ordinances, as well as NFPA
33 AND EN 16985 SAFETY STANDARDS, LATEST
EDITION, or applicable country safety standards, before
the installation, operation, or servicing of this equipment.
NOTICE
This manual lists standard specifications and service
procedures. Differences can occur between this
literature and your equipment.
Differences in local or municipal codes, manufacturer
or plant requirements, material delivery requirements,
and more can make variations unpreventable. To
find these differences, compare this manual to your
system installation drawings and other applicable Binks
equipment manuals.
EN03 SAFETY
www.binks.com25-0634_EN R6 (01/2025) 4 / 76
AREAS
Indicate possible
hazard occurrences.
HAZARDS
Indicate possible hazards.
SAFEGUARDS
Prevention of possible hazards.
Spray Areas Fire Hazards
Improper or unsatisfactory
operation and maintenance
procedures will cause a fire
hazard.
If the safety interlocks are
disabled during operation,
protection against accidental
arcing is shut off and can cause
a fire or explosion.
Frequent Power Supply or
Controller shutdown identifies a
problem in the system. For this
occurrence, a correction will be
necessary
Fire extinguishing equipment must be present in the
spray area. Periodically run a test to make sure the
equipment stays usable.
Keep spray areas clean to prevent the build-up of
combustible residues.
Do not smoke in the spray area.
The high voltage supplied to the atomizer must be
turned off before the equipment is cleaned, flushed
or maintained.
Spray booth ventilation must be kept at the rates as
set by NFPA-33, OSHA, country, local, and municipal
codes.
If flammable or combustible solvents are used to
clean the equipment, ventilate the area.
Prevent electrostatic arcing. Maintain spark-safe
work distance between the parts that get coated and
the applicator. A span of one inch for every 10KV of
the output voltage is necessary.
Do an equipment test only in areas free of
combustible material. The test may necessitate the
high voltage to be on, but only as instructed.
Non-factory replacement parts or unauthorized
equipment modifications can cause a fire or injury.
The key switch bypass is used only during setup
operation.
Do no production work with disabled safety
interlocks.
Set up and operate the paint procedure and
equipment under NFPA-33, NEC, OSHA, local,
municipal, country, and European Health and Safety
Norms.
EN 03 SAFETY
www.binks.com 25-0634_EN R6 (01/2025) 5 / 76
AREAS
Indicate possible
hazard occurrences.
HAZARDS
Indicate possible hazards.
SAFEGUARDS
Prevention of possible hazards.
Spray Areas
General Use and
Maintenance
Explosion Hazard
Improper or unsatisfactory
operation and maintenance
procedures will cause a fire or
explosion hazard.
If the safety interlocks are
disabled during operation,
protection against accidental
arcing is shut off and can cause
a fire or explosion.
Frequent Power Supply or
Controller shutdown identifies a
problem in the system. For this
occurrence, a correction will be
necessary.
Improper or unsatisfactory
operation and maintenance
procedures will cause a fire
hazard.
Personnel must be correctly
trained in the operation and
maintenance of this equipment.
Prevent electrostatic arcing. Maintain spark-safe
work distance between the parts that get coated and
the applicator. A span of one inch for every 10KV of
output voltage is necessary.
Unless specifically approved for use in hazardous
locations, put all electrical equipment outside of
Class I or II, Division 1 or 2 hazardous areas in
accordance with NFPA-33, or outside of Zone 2 or
Zone 22 in accordance with EN standards.
If equipped, set the current overload sensitivity as
described in the related section of the equipment
manual. If incorrectly set, the current overload
sensitivity for protection against accidental arcing is
turned off and can cause a fire or explosion.
Frequent power supply shutdown indicates a
problem in the system, which requires correction.
Always turn off the control panel power before the
system is flushed, cleaned, or servicing the spray
system equipment. Make sure no objects are within
the spark-safe work distance before the high voltage
is turned on.
The control panel must interlock with the ventilation
system and conveyor in accordance with NFPA-33,
EN 50176.
Fire extinguishing equipment must be present in the
spray area. Periodically run a test to make sure the
equipment stays usable. Do an equipment test only
in areas free of combustible material.
Train all personnel in accordance with the
requirements of NFPA-33, EN 60079-0.
Before equipment operation, personnel must read
and understand these instructions and safety
precautions.
Obey appropriate local, municipal, state, and
national codes governing ventilation, fire protection,
operation maintenance, and housekeeping.
Reference OSHA, NFPA-33, EN Norms, and your
insurance company requirements.
EN03 SAFETY
www.binks.com25-0634_EN R6 (01/2025) 6 / 76
AREAS
Indicate possible
hazard occurrences.
HAZARDS
Indicate possible hazards.
SAFEGUARDS
Prevention of possible hazards.
Spray Area High
Voltage Equipment
Electrical Discharge
This equipment contains a
high-voltage device that can
cause an electrostatic induction
on ungrounded objects. This
electrical charge is capable of
igniting coating materials.
Insufficient ground will cause a
spark hazard. A spark can ignite
many coating materials and
cause a fire or explosion.
Operators in the spray area and the parts to be
sprayed must be sufficiently grounded.
All conductive objects inside the spray area must be
grounded.
Hold the parts that get sprayed on conveyors or
hangers that are correctly grounded. The resistance
between the parts and the earth-ground must not be
more than 1 MΩ. Refer to: NFPA-33.
Before the equipment is operated, round all
operators. They cannot wear rubber-soled insulated
shoes. Wear ground straps on wrists or legs for
sufficient ground contact.
Operators must not wear or carry ungrounded metal
objects.
When used, operators must make complete contact
with the applicator handle and electrostatic gun. Use
conductive gloves or gloves with the palm section cut
out.
Operators must not wear grounded footwear.
NOTE: REFER TO NFPA-33 OR SPECIFIC
COUNTRY SAFETY CODES FOR GUIDANCE TO
CORRECTLY GROUND THE OPERATOR.
Except for objects needed for the high-voltage
process, all electrically conductive objects in the
spray area are to be grounded. Supply a grounded
conductive floor in the spray area.
Always turn off the applicator voltage before the
system is flushed, cleaned, or when servicing the
spray system equipment.
Unless specifically approved for use in hazardous
locations, put all electrical equipment outside of
Class I or II, Division 1 or 2 hazardous areas in
accordance with NFPA-33, or outside of Zone 2 or
Zone 22 in accordance with EN standards.
Do not install an applicator into a fluid system if the
solvent supply is ungrounded.
Do not touch an energized applicator electrode.
EN 03 SAFETY
www.binks.com 25-0634_EN R6 (01/2025) 7 / 76
AREAS
Indicate possible
hazard occurrences.
HAZARDS
Indicate possible hazards.
SAFEGUARDS
Prevention of possible hazards.
Spray Areas
Spray Area and
Equipment Use
Toxic Fluid or Fumes
Toxic fluids or fumes can cause
severe injury or death if splashed
in the eyes or on the skin, or if
inhaled or swallowed.
High-pressure fluid sprayed
from the gun, hose fittings, or
ruptured/damaged components
can pierce the skin.
While this injury can appear as
cut skin, this is a severe injury
that can result in the amputation
of the affected area.
Read the Safety Data Sheet (SDS) for instructions
to know and understand how to handle the specific
hazards of the fluids used, and the effects of long-
term exposure.
During the spray, clean, or servicing of equipment,
or when in the work area, keep the work area fully
ventilated.
Always wear personal protective equipment (PPE)
when in the work area or during equipment operation.
Refer to the Personal Protective Equipment warnings
in this manual.
Store hazardous fluid in approved containers and
refer to local, municipal, state, and national codes
governing the disposal of hazardous fluids.
Do not point or operate the spray gun at the body
part of a person.
Do not put your hand or fingers over the gun fluid
nozzle or fittings in the hose or Proportioner.
Do not try to stop or deflect leaks with your hand,
glove, body, or shop rag.
Do not blowback fluid, as the equipment is not an
air spray system.
Relieve pressure in the supply hoses, Proportioner,
and QuickHeat™ hose before the equipment is
inspected, cleaned, or serviced.
Use the lowest possible pressure to recirculate,
purge, or troubleshoot the equipment.
Examine the hoses, couplings, and fittings every day.
Service or immediately replace parts that leak, are
worn, or are damaged. Replace high-pressure hose
sections. They cannot be recoupled or serviced.
EN03 SAFETY
www.binks.com25-0634_EN R6 (01/2025) 8 / 76
AREAS
Indicate possible
hazard occurrences.
HAZARDS
Indicate possible hazards.
SAFEGUARDS
Prevention of possible hazards.
Equipment
and Fluids
Pressurized
Aluminum Parts
Skin and Clothing Burns
Equipment surfaces and fluids
can become very hot during
operation.
The use of certain solvents and
chemicals can cause equipment
damage and severe personal
injury.
Do not touch hot fluid or equipment during operation.
Do not let clothing touch the equipment during
operation or immediately after the equipment is
stopped.
Let the equipment fully cool before the examination
or servicing of the component.
Do not use 1,1,1-trichloroethane, methylene
chloride or other halogenated hydrocarbon solvents
or fluids that contain such solvents.
These solvents can cause a severe chemical
reaction and equipment rupture that results in
equipment and property damage, serious bodily
injury, or death.
EN 03 SAFETY
www.binks.com 25-0634_EN R6 (01/2025) 9 / 76
AREAS
Indicate possible
hazard occurrences.
HAZARDS
Indicate possible hazards.
SAFEGUARDS
Prevention of possible hazards.
Spray Areas Do Not Touch
The effect of paint flow rates
and formulations on the quality
of atomization can cause the
turbines to rotate at high speeds.
Do not use a rag or gloved hand against the bell
edge to stop or slow down a bell during rotation.
Do not try to clean the bell edge during rotation.
EN03 SAFETY
www.binks.com25-0634_EN R6 (01/2025) 10 / 76
If the operation of this equipment, sensors, switches, or other ancillary equipment occurs in the presence of flammable
gases and vapors, connect this equipment through intrinsic-safe or Zener barriers. Classify them as a ‘simple apparatus’
or approve them for use in these areas.
ADDITIONAL SAFETY INFORMATION
Observe all local or municipal safety measures and wear approved protective equipment when servicing this equipment.
Clean all spilled chemicals and materials and do all work in a clean and organized environment to prevent personal
injury and equipment damage.
NOTICE
During the initial commission of the equipment and at periodic times throughout equipment life, visually examine all
fluid fittings for leaks.
Periodically, it is necessary to visually examine all pieces of this equipment for signs of noticeable degradation due to
chemicals or other conditions in the equipment’s environment.
CAUTION
Only operate the equipment after you have read this section.
DANGER
To prevent injury or electrocution while the system is under power, do not contact, disconnect, or manipulate electrical
connections or devices. The main disconnect on the right side of the controller can be locked out. Follow the proper
Lockout–Tagout (LOTO) procedures for internal controller electrical work.
Only qualified electrical personnel can perform the work if diagnosis and troubleshooting are not possible during
working conditions.
WARNING
To prevent possible chemical spillage when personnel are not on site, air and fluid supplies for the equipment must be
disabled when the equipment idles for an extended period, such as an end-of-day shutdown.
SAFETY
Obey local or municipal regulations that require installed fire suppression for equipment operation.
EN 04 INTRODUCTION
www.binks.com 25-0634_EN R6 (01/2025) 11 / 76
04 INTRODUCTION
SYSTEM OVERVIEW
The i-Flow SE System is composed of five basic elements.
• Main Controller
• Shot Meter
• Purge Stand
• Lubricator
• Pump(s) - Pictured is Binks pump (which may or may not be supplied by Binks).
Main Controller
Shot Meter
Dispense Gun
Purge StandLubricatorPumpsY-Stands
EN04 INTRODUCTION
www.binks.com25-0634_EN R6 (01/2025) 12 / 76
I-FLOW SE CONTROLLER SPECIFICATIONS
Power Requirements: Standard: 220 VAC, 1ph, 50/60Hz @ 15.0A
Full Load Amps: @220V 12.0 A (Single Controller)
Disconnect Rated: 30 A (Through Door Type)
w/ Internal Lock-Out for Safety
Operating Temperature Range: 40o - 140o F (4-60o C)
Operarting Humidity Range: 0 - 70% Non-Condensing
Interface Connection: DeviceNet, ProfiNet, Ethernet IP,
Wired 24V dc, other
Box Size: 36h x 24w x 12d
HMI Size: 12 inch Touch Screen
EN 04 INTRODUCTION
www.binks.com 25-0634_EN R6 (01/2025) 13 / 76
I-FLOW SE CONTROLLER (FOR HEAT) SPECIFICATIONS
Toyota Cream
Provisions to mount above robot
controller and cabling out the left side.
Power Requirements: Standard: 220 VAC, 1ph, 50/60Hz @ 15.0A
Full Load Amps: @220V 12.0 A (Single Controller)
Disconnect Rated: 30 A (Through Door Type)
w/ Internal Lock-Out for Safety
Operating Temperature Range: 40o - 140o F (4-60o C)
Operarting Humidity Range: 0 - 70% Non-Condensing
Interface Connection: DeviceNet, ProfiNet, Ethernet IP,
Wired 24V dc, other
Box Size: 36h x 24w x 12d
HMI Size: 12 inch Touch Screen
EN04 INTRODUCTION
www.binks.com25-0634_EN R6 (01/2025) 14 / 76
CONTROL PANEL NUMBER
EN 04 INTRODUCTION
www.binks.com 25-0634_EN R6 (01/2025) 15 / 76
SHOT METER SPECIFICATIONS
25-0634 70cc E-Doser, Side Mount No Gun
25-0636 70cc E-Doser, Side Mount with Gun
Assembly View (Front)
Wire Harness
35-6045
Linear Transducer
70cc 35-5119
Pressure Transducer
35-7006
Servo Motor
70cc 35-7273
Material Body
70cc 40-5941
Dispense Valve
25-0502 Standard
25-0508 1/2 JIC
25-0504 3/4 JIC
Cone Tip
40-4652-030 Tip 0.030
40-4652-045 Tip 0.045
40-4652-050 Tip 0.050
40-4652-060 Tip 0.060
40-4652-090 Tip 0.090
40-4652-115 Tip 0.115
40-4652-150 Tip 0.150
40-4652-250 Tip 0.250
EN04 INTRODUCTION
www.binks.com25-0634_EN R6 (01/2025) 16 / 76
SHOT METER SPECIFICATIONS
25-0634 70cc E-Doser, Side Mount No Gun
25-0636 70cc E-Doser, Side Mount with Gun
Assembly View (Back)
Refill Solenoid
35-3426
Dispense Solenoid
35-3426
Throat Seal
70cc 35-6510
Refill Valve
70cc 10-1098 Low Flow
10-1771 High Flow
Seat
70cc 40-5397 Low Flow
40-5072 High Flow
EN 04 INTRODUCTION
www.binks.com 25-0634_EN R6 (01/2025) 17 / 76
E-Doser 70cc SPECIFICATIONS
Weight: 97 lbs. (44.0 kg
Maximum Working Prressure: 3200 PSI (220 bar) (Outlet Orifice and Viscosity Dependent)
Maximum Flow Rate: 13.4 cc/sec (Outlet Orifice and Viscosity Dependent
Maximum Volume: 79cc
Usable Volume: 72cc
Air Inlet: 3/8 NPT (#8 JICM Fitting Provided)
Plant Air 80 to 110 PSI (5.5 to 7.6 bar)
Material Inlet: 1/2 NPT (#8 JICM Fitting Provided)
(Minimum 1800 PSI (124 bar))
Material Outlet: #12 JICM or #8 JICM or 1/2-20 Tip Adaptor (STD) (0.270 Orifice)
EN04 INTRODUCTION
www.binks.com25-0634_EN R6 (01/2025) 18 / 76
SYSTEM INTERACE
Robot Controller
i-Flow Outputs
SYSTEM READY
VOLUME OK
IN PROCESS
MAJOR FAULT
i-Flow Inputs
STYLE (1-27)
STYLE STROBE
GUN ON / GUN OFF
FLOW COMMAND
i-Flow Outputs
PUMP ON
BEACON: PUMP OK
BEACON: EMPTY
BEACON: STANDBY
i-Flow Outputs
DISPENSE VALVE OPEN
REFILL VALVE OPEN
SERVO VALVE SIGNAL
i-Flow Inputs
MATERIAL PRESSURE
POSITION TRANSDUCER
TEMPERATURE (RTD)
POSITION (MLDT)
i-Flow Inputs
PUMP PRESURIZED
DRUM LOW
DRUM EMPTY
HANDLE POSITION
i-Flow Controller
Controller Cabinet
May Differ
Shot Meter
EN 04 INTRODUCTION
www.binks.com 25-0634_EN R6 (01/2025) 19 / 76
INSTALLATION
System Guidelines:
Installation Prints:
Drawings and information contained in this section of the manual is applicable to most installations. However in some
special cases, Binks may supply custom installation drawings for your specific site. It is highly recommended that if your
installation differs significantly from the installation drawings supplied by Binks, that you notify your Binks representative
to insure that standard installation practices are not violated and to have your prints updated to reflect the installation
accurately for future reference.
Cable Assemblies:
Interconnections between all control panels are made using manufactured cable assemblies with heavy duty
connectors. This simplifies installation and eliminates the possibility of items being wired incorrectly. The installation
requires a cable with the proper 22-pin connector on one end (P/N: 35-7007).
Equipment Grounding:
All panels should be grounded in accordance with either the National Electrical Code or local electrical codes
(whichever is more stringent). Refer to the electrical installation drawings provided in this manual to locate the
grounding terminal for all control panels.
If in doubt, contact your Binks representative for clarification.
Equipment Locations:
All of the Binks panels must be located outside of the hazardous area.
If in doubt, contact your Binks representative for clarification.
EN04 INTRODUCTION
www.binks.com25-0634_EN R6 (01/2025) 20 / 76
This page intentionally left blank.
EN 05 SHOT METER ASSEMBLY
www.binks.com 25-0634_EN R6 (01/2025) 21 / 76
05 SHOT METER ASSEMBLY
ASSEMBLY VIEWS (70CC)
PARTS LIST List (Major Components Only, for Complete Listing See Assemnly Drawing)
PARTS LIST
DETAIL QUANTITY PART NO. DESCRIPTION
A 2 35-3426 REFILL /DISPENSE SOLENOID VALVE
B 1 35-7006 PRESSURE TRANSDUCER
C 1 35-3553 RTD / TEMPERATURE SENSOR
D 1 25-0502 DISPENSE VALVE – STANDARD NOZZLE
E 1 35-6045 WIRING HARNESS
F 1 40-5695 SHOT METER BODY
G 1 35-5119 LINEAR TRANSDUCER
H 1 10-1805 REFILL VALVE
I 1 35-6942 SERVO MOTOR, E-DOSER
J 1 35-7260 BEARING PACK
K 1 35-7264 GEAR BOX
L 1 35-7261 ROLLER SCREW W/NUT
M 1 40-6014 DISPENSE EXTENSION BLOCK
N 1 35-6971 MOTOR POWER CABLE
O 1 35-6970 MOTOR ENCODER CABLE
P 1 35-6263 AIR SUPPLY FILTER 5 MICRON
Q 4 35-7262 ROLLER CARRIAGE
R 1 35-3124 INLET ADAPTOR #12 JICM x 1/2 NPT
S 1 35-6560 INLET ADAPTOR ELBOW SWIVEL #12 JIC
T 2 35-3426 DISPENSE & REFILL SOLENOID
A
20E
20L
20J
20K
20I
N
O M
G
Q
B
C
D
F
E
S
H
P
T
EN05 SHOT METER ASSEMBLY
www.binks.com25-0634_EN R6 (01/2025) 22 / 76
REBUILD KITS
Rebuild Kits for Dispense and Refill Valve
Consult Dispense / Refill Manual for complete details.es
25-0634-RK REBUILD KIT, 70CC E-DOSER
PART NO. QUANTITY DESCRIPTION
35-1055 36 TUBING, NYLON 1/4 OD BLACK ( Cut to 36 inches )
35-1505 36 TUBING, NYLON 1/4 OD YELLOW ( Cut to 36 inches )
35-1622 36 TUBING, NYLON 1/4 OD BLUE ( Cut to 36 inches )
35-4885 36 TUBING, NYLON 1/4 OD WHITE ( Cut to 36 inches )
35-3426 2 SOLENOID VALVE 24VDC VITON SEAL
35-6599 1 BODY PLUG O-RING, VITON 44mm X 50mm
35-6305 1 SEAL FLUORTREL 1-1/8 x 1-3/4
35-6315 24 TUBING, POLYURETHANE 8mm OD CLEAR
35-6510 1 SEAL UHMWPE 1-1/8 x 1-3/4 x 1/2 TRIPLE LIP
10-1938 2 FITTING, 8mmT x 1/8 Rc
35-6321 1 CARTRIDGE O-RING, VITON 1-13/16 X 2
35-6602 1 OIL TUBE O-RING VITON 2-3/4 X 2-7/8
35-7259 2 COVER GROMMET for OIL TUBING
35-6474 1 FILTER ELEMENT 5 MICRON, SPRING & O-RING KIT
NHA-532 12' TUBING, NYLON 5/32
SPARE PART / REPAIR KITS - OREDED SEPARATELY
PART NO. QUANTITY DESCRIPTION
40-5884 1 PLUNGER ROD, 70cc E-DOSER
25-0502-RK 1 REPAIR KIT, DISPENSE VALVE STANDARD
25-0508-RK 1 REPAIR KIT, DISPENSE VALVE 1/2 JIC
25-0804-RK 1 REPAIR KIT, DISPENSE VALVE 3/4 JIC
10-1805-RK 1 REPAIR KIT, REFILL VALVE ASM LOW FLOW
10-1771-RK 1 REPAIR KIT, REFILL VALVE ASM HIGH FLOW
EN 05 SHOT METER ASSEMBLY
www.binks.com 25-0634_EN R6 (01/2025) 23 / 76
SPECIAL TOOLS
EN05 SHOT METER ASSEMBLY
www.binks.com25-0634_EN R6 (01/2025) 24 / 76
This page intentionally left blank.
EN 05 SHOT METER ASSEMBLY
www.binks.com 25-0634_EN R6 (01/2025) 25 / 76
LOCK-OUT / TAG-OUT
Lock-Out / Tag-Out
1. Shut off the supply pump air motor, relieve material pressure at the pump and depressurize by following pump
manufacturer recommended process. This may differ depending on the pump manufacturer.
Depressurizing the System
2. At the control panel, select MANUAL, then press yes.
3. Press Value Refill, Valve Dispense, and any Remote valves to open these valves.
4. Watch Pressure Display reading deplete to 0 psi.
5. Press Valve Refill, Valve Dispense, and any Remote Valve to close these valves.
WARNING
High pressure can cause bodily injury.
Depressurize material, water and air system.
2
4
3 5
EN05 SHOT METER ASSEMBLY
www.binks.com25-0634_EN R6 (01/2025) 26 / 76
Lock-Out / Tag-Out (Standard Controller)
6. At the controller, turn the power off by rotating the power switch.
7. Place lock out / tag out lock on the inside of panel, or in the panel front power switch.
ONON
OFFOFF
6
7
EN 05 SHOT METER ASSEMBLY
www.binks.com 25-0634_EN R6 (01/2025) 27 / 76
TOOLS REQUIRED
• 3mm / 4mm / 5mm / 6mm / 8mm Allen Wrenches
• Adjustable Wrenches
• Flathead and Phillips Screwdrivers
• Pliers
• Flathead and Phillips Screwdrivers
• Soft Jaw Vise
MATERIAL REQUIRED
• PPE
• Loctite 567 Thread Sealant
• Mobil Mobilith SHC PM 460 Lithium Complex Synthetic Grease or Equivalent
• Clean Rags
DISASSEMBLY PROCEDURES
Disconnecting Shot Meter for Service
1. Unscrew and pull out the electrical connector to disconnect it from the Shot Meter Assembly.
2. Use an adjustable wrench to remove supply air line from the Manifold Block.
3. Use an adjustable wrench to remove the material supply hoses from the Material Block.
Back View
EN05 SHOT METER ASSEMBLY
www.binks.com25-0634_EN R6 (01/2025) 28 / 76
4. Remove the two oil tubes going to each Oil Seal Cup from the push lock fittings.
a. Remove opposite ends of the two oil tubes so that the open end of each tube can be inserted into the push lock
fitting creating two closed loops.
EN 05 SHOT METER ASSEMBLY
www.binks.com 25-0634_EN R6 (01/2025) 29 / 76
5. Place the lower oil tube from each Oil Seal Cup into a small cup and let the oil from the Oil Seal Cups drain into the
cup.
a. When the oil stops draining or slows to an intermittent drip proceed to the next step.
5
EN05 SHOT METER ASSEMBLY
www.binks.com25-0634_EN R6 (01/2025) 30 / 76
6. Insert the open tube end into the open push lock fitting for all lines so that you create two closed loops.
EN 05 SHOT METER ASSEMBLY
www.binks.com 25-0634_EN R6 (01/2025) 31 / 76
7. If necessary, use an adjustable wrench to disconnect the material hose from the Dispense Valve on the Shot Meter
Body.
7
EN05 SHOT METER ASSEMBLY
www.binks.com25-0634_EN R6 (01/2025) 32 / 76
8. Properly support and secure Shot Meter to prevent damage to person or machine.
9. While securely supporting the Shot Meter, using an 8mm Allen Wrench loosen the 8– M10 socket head cap screws
securing the Shot Meter to the mounting bracket enough to remove the Shot Meter from the robot.
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
9
EN 05 SHOT METER ASSEMBLY
www.binks.com 25-0634_EN R6 (01/2025) 33 / 76
8. Properly support and secure Shot Meter to prevent damage to person or machine.
9. While securely supporting the Shot Meter, using an 8mm Allen Wrench loosen the 8– M10 socket head cap screws
securing the Shot Meter to the mounting bracket enough to remove the Shot Meter from the robot.
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
9
EN05 SHOT METER ASSEMBLY
www.binks.com25-0634_EN R6 (01/2025) 34 / 76
Removing the Wire Harness
1. Disconnect the connectors from the Pressure Transducer.
2. Disconnect the connectors from the Temperature Sensor.
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
1
2
EN 05 SHOT METER ASSEMBLY
www.binks.com 25-0634_EN R6 (01/2025) 35 / 76
3. Disconnect the airline from the Solenoid air manifold.
4. Using a Philips screwdriver disconnect the electrical connectors by removing one Philips screw from each of the
Solenoid Valves.
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
4
3
EN05 SHOT METER ASSEMBLY
www.binks.com25-0634_EN R6 (01/2025) 36 / 76
5. Disconnect the connector from Linear Transducer.
6. Disconnect the wire harness from Shot Meter using a 3mm Allen Wrench to remove the (2) M4 SHCS.
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
5
6
EN 05 SHOT METER ASSEMBLY
www.binks.com 25-0634_EN R6 (01/2025) 37 / 76
Removing the Pressure Transducer and Temperature Sensor
1. Use an 3/4 open end wrench to remove the Pressure Transducer.
2. Use an 9/16 open end wrench to remove the Temperature Sensor.
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
1
2
EN05 SHOT METER ASSEMBLY
www.binks.com25-0634_EN R6 (01/2025) 38 / 76
Removing the Linear Transducer
1. Use an adjustable wrench to remove the MLDT Sensor.
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
1
MLDT Sensor
(Reference)
EN 05 SHOT METER ASSEMBLY
www.binks.com 25-0634_EN R6 (01/2025) 39 / 76
Removing the Air Tubes
1. Disconnect air tubes to the supply air manifold.
2. Disconnect air tubes to the refill valve.
3. Disconnect air tubes to the dispense valve.
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
1
2
3
EN05 SHOT METER ASSEMBLY
www.binks.com25-0634_EN R6 (01/2025) 40 / 76
Solenoid Valve Removal
1. Use a Philips head screwdriver to remove the (2) cap screws to remove the electrical connectors (if not already
removed).
2. Use a small Flat head screwdriver to remove the (3) cap screws and remove the Solenoid Valve (2).
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
1
2 2
EN 05 SHOT METER ASSEMBLY
www.binks.com 25-0634_EN R6 (01/2025) 41 / 76
Air Manifold Removal
1. Disconnect the Air Manifold by removing the (2) M5 SHCS using a 4mm Allen wrench.
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
1
EN05 SHOT METER ASSEMBLY
www.binks.com25-0634_EN R6 (01/2025) 42 / 76
Shot Meter Body Removal
2. Use an 8mm Allen wrench to remove the (8) M10 SHCS and washers from the Shot Meter Body.
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
2
EN 05 SHOT METER ASSEMBLY
www.binks.com 25-0634_EN R6 (01/2025) 43 / 76
3. Remove the Shot Meter Body from the Shot Meter.
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
2
EN05 SHOT METER ASSEMBLY
www.binks.com25-0634_EN R6 (01/2025) 44 / 76
Shot Meter Cover Removal
4. Use an 6mm Allen Wrench to remove the (14) M8 SHCS and washers from the front cover plate of the Shot Meter.
5. Remove the cover plate.
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
4
5
EN 05 SHOT METER ASSEMBLY
www.binks.com 25-0634_EN R6 (01/2025) 45 / 76
Shot Meter Access to Carridge Assembly
6. Use an 6mm Allen wrench to remove the (7) M8 SHCS and washers from the cover plate of the Shot Meter.
7. Use a Dowel Puller to remove the (3) dowel pins from the cover plate.
8. Remove the cover plate from the Shot Meter.
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
6
7
8
EN05 SHOT METER ASSEMBLY
www.binks.com25-0634_EN R6 (01/2025) 46 / 76
Oil Cup Removal
1. Remove the 2 air fittings from the Oil Cup by:
• Use a 9/16 open end wrench to remove the compression fitting and plastic tubing.
• Use a 12mm (or 1/2) open end wrench to remove the Adapter from the Oil Cup.
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
CAUTION
CAUTION! Once the 2 air fittings are removed the Oil Cup can slide off the Displacement Rod – ensure you are
supporting the weight of the Oil Cup as the air fittings are removed.
1
Compression
Fitting and Oil
Tubing
Adapter
EN 05 SHOT METER ASSEMBLY
www.binks.com 25-0634_EN R6 (01/2025) 47 / 76
2. Remove the Oil Cup from the Shot Meter.
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
2
EN05 SHOT METER ASSEMBLY
www.binks.com25-0634_EN R6 (01/2025) 48 / 76
Oil Cup Seal Removal
3. Remove the seal and snap ring from the Oil Cup. (Clean with Isopropyl Alcohol if necessary).
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
2
EN 05 SHOT METER ASSEMBLY
www.binks.com 25-0634_EN R6 (01/2025) 49 / 76
Dispense Rod Removal
1. Unscrew and remove the dispense rod from the bearing mount plate.
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
1
EN05 SHOT METER ASSEMBLY
www.binks.com25-0634_EN R6 (01/2025) 50 / 76
Motor Removal
1. Use an 8mm Allen wrench to unscrew the (4) M8 SHCS that secure the Motor.
2. Remove the Motor from the Shot Meter.
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
1
2
EN 05 SHOT METER ASSEMBLY
www.binks.com 25-0634_EN R6 (01/2025) 51 / 76
Roller Screw / Bearing Pack Removal
1. Use an 6mm Allen wrench to remove the (14) M8 SHCS and washers from the front cover plate of the Shot Meter.
2. Remove the cover plate.
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
1
2
EN05 SHOT METER ASSEMBLY
www.binks.com25-0634_EN R6 (01/2025) 52 / 76
3. Use an 6mm Allen wrench to remove the (12) M8 SHCS and washers from the top cover plate of the Shot Meter.
4. Use a Dowel Puller to remove the (6) dowel pins from the top cover plate.
5. Remove the top cover plate.
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
3
4
5
EN 05 SHOT METER ASSEMBLY
www.binks.com 25-0634_EN R6 (01/2025) 53 / 76
6. Use a 4mm Allen wrench to remove the (6) M5 SHCS from the roller screw.
7. Remove the roller screw.
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
6
7
EN05 SHOT METER ASSEMBLY
www.binks.com25-0634_EN R6 (01/2025) 54 / 76
Roller Screw / Gear Box Removal
8. Use an 6mm Allen wrench to remove the (4) M8 SHCS and washers from each side cover plate.
9. Use a Dowel Puller to remove the (2) dowel pins from each side cover plate.
10. Remove the front plate.
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
8
9
10
EN 05 SHOT METER ASSEMBLY
www.binks.com 25-0634_EN R6 (01/2025) 55 / 76
Roller Screw / Bearing Pack Removal
11. Use a 4mm Allen wrench to remove the (6) M5 SHCS from the roller screw.
12. Remove the roller screw.
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
11
2
EN05 SHOT METER ASSEMBLY
www.binks.com25-0634_EN R6 (01/2025) 56 / 76
REFILL / DISPENSE VALVES
Dispense and Refill Valve Removal
1. If the valve being replaced is on the Shot Meter, disconnect the media hose.
2. Use a 4mm Allen wrench to unscrew the (4) M5 SHCS that secure the Refill and the Dispense Valves.
3. Remove the valves from the system.
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
Dispense Valve Refill Valve
Dispense Valve
Refill Valve
2
2
1
1
EN 05 SHOT METER ASSEMBLY
www.binks.com 25-0634_EN R6 (01/2025) 57 / 76
4. If Seal Cartridge is left in Shot Meter, extract from Shot Meter Body using a pair of pliers.
DANGER
Properly Secure & Support Shot Meter while performing this procedure. Due to the weight of the unit, extra care is
required.
NOTICE
See Dispense / Refill Valve Manual for complete information and maintenance.
CAUTION
When re-assembling, insure that Seal Cartridge Pin is properly aligned with notch.
If not, damage to body or refill valve can occur.
Seal Cartidge
Pin Notch
Refill ValveSeal Cartidge
Consult Dispense / Refill Valve
Manual when replacing SEAT.
Use Loctite 567 Thread Sealant
on seat threads when replac-
ing SEAT.
EN06 SHOT METER BODY
www.binks.com25-0634_EN R6 (01/2025) 58 / 76
06 SHOT METER BODY
ASSEMBLY VIEWS, 70CC
C
B
I A
H
G
J
K
N
D
M
L
E
F
IN SHOT METER
BODY
EN 06 SHOT METER BODY
www.binks.com 25-0634_EN R6 (01/2025) 59 / 76
SHOT METER BODY PARTS LIST, 70CC
PARTS LIST
DETAIL QUANTITY PART NO. DESCRIPTION
A 1 40-5941 SHOT METER BODY
B 1 35-3553 RTD (TEMP SENSOR)
C 1 35-7006 PRESSURE TRANSDUCER
D 1 10-1805 REFILL VALVE LOW FLOW
E 1
40-1694-050 VALVE ADAPTOR BUTTON - 1/2-13 TAP
40-1694-038 VALVE ADAPTOR BUTTON - 3/8-16 TAP
40-1694-025 VALVE ADAPTOR BUTTON - 1/4-20 TAP
40-1694-010 VALVE ADAPTOR BUTTON - 10-32 TAP
F 2 35-2323 ValVE ADAPTOR BUTTON O-RINGS
G 1 356510 THROAT SEAL UHMWPE
H 1 40-4998 THROAT SEAL CARTRIDGE RETAINER
I 1 40-4997 THROAT SEAL CRATRIDGE
J 1 40-5984 REFILL VALVE SEAT LOW FLOW LARGE THREAD
K 1 35-0536 REFILL VALVE SEAT O-RING (LOW FLOW)
L 1 35-6599 DOSER BODY PLUG, O-RING VITON 44mm X 50mm
M 1 35-5918 DOSER BODY PIPE PLUG
N 1
35-3124 INLET ADAPTOR #12 JICM x 1/2 NPT
35-6560 INLET ADAPTOR ELBOW SWIVEL #12 JIC
EN06 SHOT METER BODY
www.binks.com25-0634_EN R6 (01/2025) 60 / 76
TOOLS REQUIRED
• Seat Removal and Insert Tool 40-4643 (50/100/200/300cc)
• 1/2 - 13 Threaded Stock approx. 6 in. in Length
• 3/4 in. Allen Wrench
• Arbor Press
• 5/8 in. Wrench
• Soft Jaw Vise
MATERIAL REQUIRED
• Mobil Mobilith SHC PM 460 Lithium Complex Synthetic Grease or Equivalent
DISASSEMBLY PROCEDURES
Disassembly - Throat Seals
1. If the Dispense Valve Button is left in the Shot Meter Body, remove the Dispense Valve Button assembly. [F] using
the 1/2 - 13 threaded stock and remove the o-ring [J]. See Dispense Valve section for detail description on removing
from Dispense Valve.
EN 06 SHOT METER BODY
www.binks.com 25-0634_EN R6 (01/2025) 61 / 76
2. Place Shot Meter Body in a soft jaw vise with the Refill Valve port pointing up.
3. Remove the Refill Valve Seat [M] and o-ring [N] using seal removal and insert tool, 40-4643.
4. Remove Pipe Plug Asm. [G] with O-Ring with a 3/4 in. Allen wrench.
5. Insert the pins of the upper seal cartridge tool (40-5251 for the 70cc) into the upper seal cartridge and use a 1 1/4
open end wrench to remove the Seal Cartridge from the Material Block.
6. Insert the pins of the lower seal cartridge tool (40-5250 for the 70cc) into the lower seal cartridge and use a 1 1/4
open end wrench to unscrew the lower seal cartridge from the upper seal cartridge.
6
NOTICE
The lower and upper seal cartridge are left-handed threads. Turn clockwise to loosen.
EN06 SHOT METER BODY
www.binks.com25-0634_EN R6 (01/2025) 62 / 76
ASSEMBLY PROCEDURES
1. Place the Shot Meter Body into a soft jaw vise.
2. Apply a thin film of grease to the lip of the Throat Seal [K].
3. Replace o-ring (see below)
4. Replace Throat Seal (see below)
5. Hand thread the upper seal cartridge and lower seal cartridge together by spinning counter-clockwise and ensure
you do not cross thread the seal cartridge
6. Use the lower seal cartridge tool, 40-5250 for the 70cc, upper seal cartridge tool, 40-5251 for the 70cc, and (2) 1
1/4 open end wrenches to screw the lower seal cartridge into the upper seal cartridge. Install Seal Cartridge to Shot
Meter Body by placing tool, 40-5251, in top of cartridge (see below)
7. Thread the Pipe Plug Assembly with o-ring into Shot Meter Body on the side opposite the Throat Seal and firmly
tighten using a 3/4 Allen wrench.
NOTICE
Inspect and clean all parts carefully. Replace parts if neccessary.
NOTICE
The lower and upper seal cartridge are left-handed threads. Turn counter-clockwise to tighten.
E
EN 06 SHOT METER BODY
www.binks.com 25-0634_EN R6 (01/2025) 63 / 76
Refill / Dispense Valve Seat Replacement
Removal
1. The Refill Seat is located inside the Shot Meter behind the Refill Valve.
2. With Refill Valve removed, use refill seat tool, 10-1958 (10-1959), and remove the old seat with o-ring by turning
counter-clockwise.
Install
3. With the Refill Valve removed, use refill seat tool, 10-1958 (10-1959), and insert new seat with o-ring.
• Use a medium thread lock on ALL threads.
• A small amount of grease can be put on the end of the seal removal and insertion tool to hold the seat in place
during assembly.
4. Turn clockwise and tighten new seat to a range of 80 to 100 inch pounds of torque.
EN07 REFILL
www.binks.com25-0634_EN R6 (01/2025) 64 / 76
07 REFILL
Refill Valve Assembly
Consult Dispense / Refill Manual for complete information and maintenance
CAUTION
When re-assembling, insure that Seal Cartridge Pin is properly aligned with notch.
If not, damage to body or refill valve can occur.
Seal Cartidge
Pin Notch
Refill ValveSeal Cartidge
EN 08 DISPENSE VALVE
www.binks.com 25-0634_EN R6 (01/2025) 65 / 76
08 DISPENSE VALVE
Dispense Valve Assembly
Consult Dispense / Refill Manual for complete information and maintenance
EN09 LUBRICATOR
www.binks.com25-0634_EN R6 (01/2025) 66 / 76
09 LUBRICATOR
Lubricator - Single Pump
A 5 gallon pail with diaphragm pump and 3 gallons of SEAL EXTENDER LUBRICATION OIL (SELO SYNTHETIC) .
Used to lubricate the Doser throat seal and carry away sealer / mastic solids to extend the life of the throat seal.
For additional information and maintenance, see Lubricator Service Manual.
EN 10 PURGE STAND
www.binks.com 25-0634_EN R6 (01/2025) 67 / 76
10 PURGE STAND
Purge stand, Non-Rotating
For additional information and maintenance, see Purge Stand Service Manual.
Standard Purge Stand
Sensors: Bucket in Place
EN11 MAINTENANCE
www.binks.com25-0634_EN R6 (01/2025) 68 / 76
11 Maintenance
Maintenance Schedule
Daily:
1. Verify the bead pattern and volume is correct.
2. Verify the pump handle is in the down position.
3. Lubricate pump follower seals after every barrel change.
4. Bleed air from follower after every barrel change.
5. Bleed air from foot valve after every barrel change.
6. Verify that the dispense tip is clean and not damaged.
7. Verify that all air and material gauges are functional and that the system is operating a the correct levels.
Weekly:
1. Check Shot Meter and pump for air, material, and oil leaks.
2. Verify pump pressure, elevator pressure.
3. Verify oil recirculate pressure.
4. Check electrical cables for wear and tightness.
Monthly:
1. Check oil level in recirculate reservoir.
2. Check air and material lines for tightness and wear.
3. Check air filters for contamination.
4. Check all cables and hoses for damage. Make sure all connections are secure and that no leaks are
present.
Quarterly:
1. Clean air filters .
May be sooner depending on material, production rate, and volume applied per job.
Annually:
1. Clean and rebuild Shot Meter with complete rebuild kit.
May be sooner depending on material, production rate, and volume applied per job.
2. Purge water from pump elevator.
3. Change oil and clean the oil recirculation pump.
EN 11 MAINTENANCE
www.binks.com 25-0634_EN R6 (01/2025) 69 / 76
Trouble Shooting Guide Reference
Trouble Shooting SMP Title Trouble Shooting SMP Number
Refill Fault Position RP-024-TSMP
Refill Fault Pressure RP-024-TSMP
Lo-Lo Volume RP-023-TSMP
Hi-Hi Volume RP-022-TSMP
Doser Empty RP-021-TSMP
Manual Purge Req. Mix Tube Empty RP-020-TSMP
Purge Bucket Full RP-019-TSMP
Purge Bucket Not Present RP-018-TSMP
Supply Pump Empty Minor RP-017-TSMP
Supply Pump Empty Major RP-016-TSMP
Going Beyond System Capabilities RP-015-TSMP
Consecutive Low Volume RP-014-TSMP
Consecutive High Volume RP-013-TSMP
Supply Drum A Not Present RP-012-TSMP
Supply Drum B Not Present RP-011-TSMP
Supply Drum 2A Not Present RP-010-TSMP
Supply Pump A Purge Required RP-008-TSMP
Supply Pump B Purge Required RP-007-TSMP
Position Sensor Did NOT Empty RP-006-TSMP
Position Sensor Did NOT Go Home RP-005-TSMP
Position Sensor No Refill RP-004-TSMP
Cured Tip RP-003-TSMP
Supply Pump 2A Purge Required RP-025-TSMP
Supply Pump 2B Purge Required RP-026-TSMP
Nozzle Alignment Tool Fault RP-027-TSMP
Plugged Dispense Tip RP-028-TSMP
Pump Run Away RP-029-TSMP
Pump 2 Run Away RP-030-TSMP
Position Transducer Low Pump Pressure RP-031-TSMP
Supply Pump Fluid Pressure Low RP-032-TSMP
No Supply Pumps Available RP-039-TSMP
2nd Set No Supply Pumps Available RP-040-TSMP
Supply Pump A Not Ready RP-035-TSMP
Supply Pump B Not Ready RP-036-TSMP
Supply Pump 2A Not Ready RP-037-TSMP
Supply Pump 2B Not Ready RP-038-TSMP
Supply Pumps Not Available RP-039-TSMP
Supply Pumps 2 Not Available RP-040-TSMP
Worn Tip RP-041-TSMP
Supply Pump A No Air Supply RP-042-TSMP
EN11 MAINTENANCE
www.binks.com25-0634_EN R6 (01/2025) 70 / 76
Trouble Shooting SMP Title Trouble Shooting SMP Number
Supply Pump B No Air Supply RP-043-TSMP
Supply Pump 2A No Air Supply RP-044-TSMP
Supply Pump 2B No Air Supply RP-045-TSMP
Dispense Tip Partial Plug RP-046-TSMP
Handshake Fault in Cycle Off Strobe, Gun RP-047-TSMP
Handshake Fault in Cycle Complete On Stobe Gun RP-048-TSMP
Handshake Fault Gun On Before PreCharge RP-049-TSMP
Handshake Fault Switch to Manual RP-050-TSMP
Handshake Fault Stobe Off Before Gun RP-051-TSMP
Handshake Fault Zero ID Job RP-052-TSMP
2 Part Nozzle Alignment Not Safe RP-053-TSMP
Intensifier Air Low RP-054-TSMP
Pressure Sensor1 Cable Open Circuit RP-055-TSMP
Pressure Sensor2 Cable Open Circuit RP-056-TSMP
Position Sensor1 Cable Open Circuit RP-057-TSMP
Position Sensor2 Cable Open Circuit RP-058-TSMP
RTD Sensor1 Cable RP-059-TSMP
Wrong I/O Rack or Software Installed RP-060-TSMP
Calibration Chamber Pressure Not Removed RP-061-TSMP
Dispense Valve Leak or Not Closed or Solenoid Stuck RP-088-TSMP
Dispense Cable Short or Overload RP-062-TSMP
Refill Cable Short or Overload RP-063-TSMP
InDep Disp1 Cable Short or Overload RP-064-TSMP
InDep Disp2 Cable Short or Overload RP-065-TSMP
InDep Disp3 Cable Short or Overload RP-066-TSMP
InDep Refill B Cable Short or Overload RP-067-TSMP
InDep Out A Cable Short or Overload RP-068-TSMP
InDep Out B Cable Short or Overload RP-069-TSMP
Bad Pressure Transducer RP-070-TSMP
Refill Valve Leak or Not Closed or Solenoid Stuck RP-071-TSMP
Refill Valve Not Open or Supply Below 1500 PSI RP-072-TSMP
I-O Power Supply Failure RP-073-TSMP
Materials Calibration No Refill RP-074-TSMP
Materials Calibration No Target Reached RP-075-TSMP
Bad Position Sensor RP-076-TSMP
Remote Not Open RP-077-TSMP
Refill Fault Position/Pressure 2-Part RP-078-TSMP
Refill Fault Position/Pressure ConFlow RP-079-TSMP
Lo-Lo Volume 2-Part RP-080-TSMP
Lo-Lo Volume ConFlow RP-081-TSMP
Hi-Hi Volume 2-Part RP-082-TSMP
EN 11 MAINTENANCE
www.binks.com 25-0634_EN R6 (01/2025) 71 / 76
Trouble Shooting SMP Title Trouble Shooting SMP Number
Hi-Hi Volume ConFlow RP-083-TSMP
Doser Empty 2-Part RP-084-TSMP
Doser Empty ConFlow RP-085-TSMP
Pressure Sensor2 Cable Open Circuit RP-086-TSMP
Dispense Valve Leak or Not Closed or Solenoid Stuck 2-Part RP-087-TSMP
Dispense Valve Leak or Not Closed or Solenoid Stuck ConFlow RP-088-TSMP
Refill Valve Leak or Not Closed or Solenoid Stuck 2-Part RP-089-TSMP
Refill Valve Leak or Not Closed or Solenoid Stuck ConFlow RP-090-TSMP
Refill Valve Not Open or Supply Below 1500 PSI 2-Part RP-091-TSMP
Refill Valve Not Open or Supply Below 1500 PSI ConFlow RP-092-TSMP
Consecutive Low Volume 2-Part RP-093-TSMP
Consecutive Low Volume ConFlow RP-094-TSMP
Consecutive High Volume 2-Part RP-095-TSMP
Consecutive High Volume ConFlow RP-097-TSMP
Record and Playback RP-098-TSMP
EN11 MAINTENANCE
www.binks.com25-0634_EN R6 (01/2025) 72 / 76
This page intentionally left blank.
EN 12 MANUAL REVISIONS
www.binks.com 25-0634_EN R6 (01/2025) 73 / 76
MANUAL CHANGE SUMMARY
Date Description Version
08/20/2024
Complete update: products, BOM’s, spare parts, illustrations,
separate manuals for each product.
R4
08/25/2024 Replaced 40-5916 with 40-6014 R5
1/31/2025 Re-branded to Binks R6
EN12 MANUAL REVISIONS
www.binks.com25-0634_EN R6 (01/2025) 74 / 76
This page intentionally left blank.
EN 13 WARRANTY
WARRANTY POLICY
This product is covered by Binks’ materials and workmanship limited warranty.
The use of parts or accessories from sources other than Binks will void all warranties. Failure to follow reasonable
maintenance guidance provided can invalidate the warranty.
For specific warranty information, please contact Binks.
For technical assistance or to locate an authorized distributor, contact one of our international sales
and customer support locations listed below.
www.binks.com 25-0634_EN R6 (01/2025) 75 / 76
REGION BINKS CONTACT
Americas Tel: 1-800-992-4657
Europe, Africa, Middle East Tel: +4401202571111
India marketingroa@binks.com
China Tel: +862133730108
Korea Tel: +82313663303
Japan Tel: +81457856421
Australia Tel: +61085257555
WARRANTY PAGE
EN
Binks is a global leader in innovative finishing technologies.
Binks reserves the right to modify equipment specifications without prior notice.
Binks®, DeVilbiss® and Ransburg® are registered trademarks of Binks US, LLC.
©2025 Binks US, LLC. All rights reserved.
