Resource Library
DRX Ram Outfit Manual 77-3237
- DRX Ram Outfit Manual 77-3237 - English [ English ]
77-3237
DRX60 & DRX205
Ø160mm Dual Post
DRX Ram Unit Outfits
DRX60
DRX205
INSTALLATION MANUAL
EN
ADDITIONAL RESOURCES
For additional information or copies of your service manual, please visit us online at:
binks.com/en/library
Or use this QR code with your mobile device:
XXXXXXXX
Insert
QR
code
Obey local or municipal regulations for product recycling and disposal.
IMPORTANT! DO NOT DESTROY
It is the Customer's responsibility to have all operators and service personnel read and
understand this manual.
Contact your local Binks representative for additional copies of this manual.
READ ALL INSTRUCTIONS BEFORE OPERATING THIS PRODUCT
77-3237 R3.0 (06/2025) 2/32 www.binks.com
EN
This Product is designed for use with: Solvent & Waterbased Materials
Notified body details and role:
Representative authorised to compile the technical file President @. Binks France SAS
5 Place Pierre Semard, 94130 Nogent sur Marne , Paris, France
EU Declaration of Conformity
Product Description / Object of Declaration: SR & DR RAM UNITS - DR120 (104094), DR20/30/60 (104102),
SR20 (104110), DR205 (104094). DRX RAM UNITS - DRX60
(104156), DRX205 (104157), DRi205 (104163)
Suitable for use in hazardous area:
Protection Level: NOT ATEX
This Declaration of Conformity / Incorporation is issued
under the sole responsibility of the manufacturer:
Binks U.K. Limited,
Ringwood Road,
Bournemouth, BH11 9LH. UK
Machinery Directive 2006/42/EC
by complying with the following statutory documents and harmonised standards:
EN ISO 4414:2010 Pneumatic Fluid Power - General Rules and safety requirements
EN ISO 12100:2010 Safety of Machinery - General Principles for Design
EN 12621:2006+2010 Machinery for the supply and circulation of coating materials under pressure - Safety requirements
Providing all conditions of safe use / installation stated within the product manuals have been complied with and also installed in accordance
with any applicable local codes of practice.
Signed for and on behalf of Binks
U.K. Ltd:
Document Part No.
.
This Declaration of Conformity / Incorporation is issued under the sole responsibility of the
manufacturer:
Executive President: Engineering and
Operations, Shoreview, MN, 55126. USA
F. A. Sutter
14/04/25
77-3237 R3.0 (06/2025) 3/32 www.binks.com
EN
UKCA Declaration of Conformity
This Declaration of Conformity / Incorporation is issued under the sole responsibility of the
manufacturer:
Protection Level: NOT ATEX
Supply of Machinery (Safety) Regulations 2008
by complying with the following statutory documents and designated standards:
BS EN ISO 4414:2010 Pneumatic Fluid Power - General Rules and safety requirements
BS EN ISO 12100:2010 Safety of Machinery - General Principles for Design
BS EN 12621:2006+2010 Machinery for the supply and circulation of coating materials under pressure - Safety requirements
Providing all conditions of safe use / installation stated within the product manuals have been complied with and also installed in accordance
with any applicable local codes of practice.
Executive President: Engineering and
Operations, Shoreview, MN, 55126. USA
F. A. Sutter
14/04/25
Approved body details and role:
This Declaration of Conformity / Incorporation is issued
under the sole responsibility of the manufacturer:
Binks U.K. Limited,
Ringwood Road,
Bournemouth, BH11 9LH. UK
Signed for and on behalf of Binks
U.K. Ltd:
Document Part No.
.
SR & DR RAM UNITS - DR120 (104094), DR20/30/60 (104102),
SR20 (104110), DR205 (104094). DRX RAM UNITS - DRX60
(104156), DRX205 (104157), DRi205 (104163)
Suitable for use in hazardous area:
Product Description / Object of Declaration:
This Product is designed for use with: Solvent & Waterbased Materials
77-3237 R3.0 (06/2025) 4/32 www.binks.com
ENIn this part sheet, the words WARNING, CAUTION and NOTE are used to emphasize important safety information as
follows:
WARNING CAUTION NOTE
Hazards or unsafe practices which could result in
severe personal injury, death or substantial property
damage.
Hazards or unsafe practices which could result in
minor personal injury, product or property
damage
Important installation, operation or maintenance
information.
WARNING
Read the following warnings before using this equipment.
READ THE MANUAL. Before operating finishing equipment, read and
understand all safety, operation and maintenance information
provided in the operation manual.
AUTOMATIC EQUIPMENT. Automatic
equipment may start suddenly without
warning.
WEAR SAFETY GLASSES. Failure to wear safety glasses with side
shields could result in serious eye injury or blindness.
PROJECTILE HAZARD. You may be
injured by venting liquids or gases that
are released under pressure, or flying
debris.
DE-ENERGIZE, DE-PRESSURISE, DISCONNECT AND LOCK OUT ALL
POWER SOURCES DURING MAINTENANCE. Failure to de-energize,
disconnect and lock out all power supplies before performing
equipment maintenance could cause serious injury or death. KNOW WHERE AND HOW TO SHUT
OFF THE EQUIPMENT IN CASE OF AN
EMERGENCY.
NOISE LEVELS. The A-weighted sound level of pumping and spray
equipment may exceed 85 dB(A) depending on equipment settings.
Actual noise levels are available on request. It is recommended that
ear protection is worn at all times while equipment is in use.
PRESSURE RELIEF PROCEDURE.
Always follow the pressure relief
procedure in the equipment instruction
manual.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PROVIDE THIS INFORMATION TO THE
OPERATOR OF THE EQUIPMENT.
INSPECT THE EQUIPMENT DAILY. Inspect the equipment for worn or
broken parts on a daily basis. Do not operate the equipment if you
are uncertain about its condition.
OPERATOR TRAINING. All personnel
must be trained before operating
finishing equipment.
EQUIPMENT MISUSE HAZARD. Equipment misuse can cause the
equipment to rupture, malfunction or start unexpectedly and result in
serious injury. PACEMAKER WARNING. You are in the
presence of magnetic fields which may
interfere with the operation of certain
pacemakers.HIGH PRESSURE CONSIDERATION. High pressure can cause serious
injury. Relieve all pressure before servicing. Spray from the gun,
hose leaks or ruptured components can inject fluid into your body
and cause extremely serious injury.
KEEP EQUIPMENT GUARDS IN PLACE.
Do not operate the equipment if the
safety devices have been removed.
STATIC CHARGE. Fluid may develop a static charge that must be
dissipated through proper grounding of the equipment, objects to be
sprayed and alll other electrically conductive objects in the dispensing
area. Improper grounding or sparks can cause a hazardous condition
and result in fire, explosion or electric shock and other serious injury.
NEVER MODIFY THE EQUIPMENT. Do
not modify the equipment unless the
manufacturer provides written
approval.
PROP 65 WARNING. WARNING: This product contains chemicals
known to the state of California to cause cancer and birth defects or
other reproductive harm.
PINCH POINT HAZARD. Moving parts
can crush and cut. Pinch points are
any areas where ther are moving
parts.
77-3237 R3.0 (06/2025) 5/32 www.binks.com
EN
Specification
Air Inlet 1/2 BSP F
Dirt 40 Microns
Water +7°C @ 7 bar
Feature Remarks
DRX60
DRX205
22.6kN / 5080 lbf
22.6kN / 5080 lbf
Down thrust at 6 bar air
pressure
Maximum Working Air Pressure
Oil 25mg/m³
ISO 8573-1
Class 5/5/4
Air Quality
DRX60
DRX205
DRX60
DRX205
DRX60
DRX205
DRX60
DRX205
DRX60
DRX205
Ram Stroke
Unit Height - Fully Extended
Wiper Ring Material
Weight without Pump
Drum pressure at 6 bar air
700mm / 28
960mm / 38
2180mm / 86
2625mm / 103.5
max.
EPDM
254kg / 560 lbs
7 bar / 101 psi
380kg / 836 lbs
2.2 bar / 32 psi
0.9 bar / 13 psi
Ensure container can withstand
these pressures before use.
Including Pump
Including Pump
77-3237 R3.0 (06/2025) 6/32 www.binks.com
EN
General Description
An option is available to provide automatic ‘changeover’ when using two Ram Units in Duty / Standby mode.
The pump air regulator unit (see page 23) is supplied with hose connection to the air motor.
Ram Unit Outfits are designed to ensure correct ‘priming’ of the pump fluid section inlet and to prevent
‘cavitation’ when high viscosity materials are pumped. The Ram units will accommodate industry standard barrels
of 60 & 205L.
The outfits comprise of Ram Unit, Pump and Follower plate assembly.
The Follower plate is designed to accept both chop check or ball check pumps.
A pneumatic control box (see page 22) with necessary Ram control features.
Raise and lower the ram plate.
A 'release valve' to separate the ram from the empty container.
Air pressure regulator to control Downforce pressure.
Pump Stop / Start.
The Ram plate has two seals, which accurately fit the inside of the barrel, as material is used the ram plate
descends, cleaning the sides of the barrel, reducing wastage to a minimum.
A height adjustable trip valve assembly (see page 24) is also included as standard to stop the pump when the
bottom of the container is reached.
77-3237 R3.0 (06/2025) 7/32 www.binks.com
EN
(SEE TABLE 8)
PUMP ROD
MATERIAL
(SEE TABLE 7)
PUMP PACKING
MATERIAL
(SEE TABLE 6)
60
205
205
Table 2 Ref.
TABLE 3
DESCRIPTION
EPDM
Table 1 Ref.
(SEE TABLE 3)
WIPER SEAL
MATERIAL
_ _ _ _ _ MX _ _ _ _ _ _ - _ M _
PUMP RATIO
Model Selection
Ram Unit Outfit Selection Guide
RAM SELCTION PUMP SELECTION
MANUAL PACKING
ADJUSTMENT
PUMP TYPE
(SEE TABLE 5)
(SEE TABLE 4)
RAM TYPE
(SEE TABLE 1)
DRUM VOLUME
(SEE TABLE 2)
PUMP FLUID
OUTPUT/CYCLE
TYPICAL EXAMPLE
DRX205E – MX86023PU – SMX
60
CODE
E
CODE
DRX
60L / 15 Gallon Drum
205L / 55 Gallon Drum
DESCRIPTION
TABLE 2
TABLE 1
CODE DESCRIPTION
Dual Post Ram Extreme Duty
(Ø160mm)
DRX
77-3237 R3.0 (06/2025) 8/32 www.binks.com
EN
115 200 420 860
115 200 420 860
60
115 cc/cycle
200 cc/cycle
420 cc/cycle
115
200
420
860
CODE
860 cc/cycle
DRX Rams
DESCRIPTION
TABLE 4 - Chop Check Pumps
DESCRIPTION
Table 4 Ref.
68
15:1 Pump Ratio
23:1 Pump Ratio
30:1 Pump Ratio
39:1 Pump Ratio (DRX205 Only)
43:1 Pump Ratio
46:1 Pump Ratio
66:1 Pump Ratio
68:1 Pump Ratio
DESCRIPTIONCODE
15
23
30
39
43
46
66
Table 4 Ref.
TABLE 5 - Chop Check Pumps
205
CODE DESCRIPTION
X Ram Mount Chop Check Pump
Table 4 Ref.
TABLE 6
C Nitrided Carbon Steel
S Ceramic Coated Stainless Steel
TABLE 8
CODE DESCRIPTION
PU PTFE & UHMWPE
TABLE 7
CODE
77-3237 R3.0 (06/2025) 9/32 www.binks.com
EN
The ram plate base should be mounted on a stable and level floor.
The standard ram plate has 4 off - holes Ø21mm to enable the base to be securely fixed to the floor.
Suitable floor fixing ‘rawlbolts’ should be used which are designed to suit the floor material.
DRX60
104156 - Installation
A compressed air supply is connected to the ½ BSP F connection to control the lift and lowering of the air
cylinders and supply the pump.
Base plate = 930mm x 480mm. Mounting holes = 1040mm x 400mm
77-3237 R3.0 (06/2025) 10/32 www.binks.com
EN
5. A slight delay will occur before the ram starts to move. This is to allow air to exhaust from the ‘up’ side of
the cylinder.
6. Check that the ram is going down squarely into the drum.
7. As the ram plate goes into the drum, air will be pushed out of the vent.
8. When material starts to come out of the vent, close the primer screw assembly.
9. Operate pump and system under normal operating conditions. At all times checking the pump for cavitation.
On very thick, non-flowing materials pressures up to 5 bar may be required in order to prime the pump correctly.
However high ram pressures must not be used on light free-flowing materials as leaks around the ram seals
could develop.
11. It is now time to set the speed of the Up and Down motion of the ram unit.
12. Remove the cover from the 104097 control box mounted on the ram unit leaving the hoses connected.
Operate the up / down valve and at the same time screw in or out he control valve (silencer / speed controller).
The motion needs to slow enough so that removing an empty drum can be one smooth operation, about 1 full
stroke in 30 seconds.
13. Do not use the pressure regulator to control the speed of the unit, as it will give an uneven movement.
Operation Insructions
Setting up ram trip valve
1.Make sure that the air to the pump is turned off by fully unwinding the regulator on 104098.
2.Press the on (green) button on 104098. This indicator should now be green.
3. Place an empty drum under the ram plate. With the ram pressure set at 2 bar lower the ram into the drum
until it has made contact with the bottom of the drum. When the valve is tripped the indicator will switch to red
(meaning pump off).
4. Set the trip valve so that it has just tripped, by between 5 – 10mm. Test this a number of times to make
sure that the valve trips before the ram plate contacts the bottom of the drum.
5. If different drums are to be used then checks should be made to make sure that the valve is operated.
Setting up ram force for different materials
1. Place a fresh drum of material underneath the ram plate.
2. Open the ram plate priming assembly.
3. Set the ram force to 2 bar.
4. Select the Up / Stop / Down controller to Down.
10. When the air pressure is set use the Raising the ram from a drum procedure, and remove drum from the
unit.
77-3237 R3.0 (06/2025) 11/32 www.binks.com
EN
8. When material starts to come out of the vent, close the primer screw assembly.
9. The ram is now ready to use.
Raising the ram from a drum
1. Make sure that the pump is turned off, air pressure relieved and pump pressure also relieved.
2. Select the Up / Stop / Down controller to up.
3. As the ram starts to move inject small busts of compressed air by pressing the Drum Release button
mounted on the side of the unit. This will slowly push the drum off the ram.
4. Be very carefully not to inject too much air, as air can escape between the ram plate seal and the drum. This
is not dangerous but can make an unnecessary mess that requires cleaning.
Operation
Lowering the ram onto material
1. Place a fresh drum of material underneath the ram plate.
2. Open the ram primer screw assembly.
3. Select the Up / Stop / Down controller to down.
4. Make sure that the ram force is to the correct pressure. ( see Setting up ram pressure ).
5. A slight delay will occur before the ram starts to move. This is to allow air to exhaust from the ‘up’ side of
the cylinders.
6. Check that the ram is going down squarely into the drum.
7. As the ram plate goes into the drum, air will be pushed out of the vent.
77-3237 R3.0 (06/2025) 12/32 www.binks.com
EN
NOTES
77-3237 R3.0 (06/2025) 13/32 www.binks.com
EN
1
1
1
1
1
1
1
1
2
3
3
3
3
1
1
2
1
3
3
1
6
3
1
AIR MOTOR TIE ROD
PUMP TIE ROD
DRX60 RAM PLATE ASSEMBLY
M16 LOCK WASHER
M16 HEX NUT
CONNECTION KIT - NOT SHOWN
Item Part No. Description
6
7
8
9
10
11
12
13
14
15
16
17
18
Qty. Remarks
AX260L-7R AIR MOTOR
FX200PU-CMX FLUID SECTION
FX200PU-SMX FLUID SECTION
MOTOR ROD SPLIT COLLAR
PUMP ROD QD ADAPTER
SPLIT COLLAR RETAINER
HAIRPIN CLIP
DRX60 RAM UNIT ASSEMBLY
No 2 x 4.75 RIVET
M16 PLAIN WASHER PLATED
M20 SPRING WASHER - PLATED
M20 DOME NUT - PLATED
M16 DOME NUT - PLATED
NAMEPLATE
COVER CLIP
SPLIT GUARD
MOUNTING PLATE
0115-010450
104156
164838
165097
165139
177040
177052
193540
193543
193546
194458
194459
194460
194461
20-6832
20-6834
193999
19
20
21
22
DRX60 Ram Unit Outfit Parts List
1
2
2
3
4
5
AX260L-7R
FX200PU-CMX
FX200PU-SMX
0115-010445
0115-010447
0115-010448
CMX MODEL
SMX MODEL
77-3237 R3.0 (06/2025) 14/32 www.binks.com
EN
DRX60 Ram Unit Outfit Assembly
77-3237 R3.0 (06/2025) 15/32 www.binks.com
EN
1
1
1
2
2
4
2
2
2
2
1
4
4
2m
2m
NOT SHOWN
NOT SHOWN
RAM CONTROL BOX
RAM AIR REG SETUP
DRX TRIP ROD KIT
M16 SPRING WASHER
M16 x 70 HEX HD BOLT
M4 x 45 SOCKET HD CAP SCREW
M24 SAFETY WASHER
M24 DOME NUT
¼ - Ø6 PUSH IN ELBOW
DRUM STOP
DRX60 BARE RAM UNIT
M4 NYLOC NUT
M4 WASHER
Ø6 x 4 PU HOSE - BLACK
Ø4 x 2.5 PU HOSE - BLACK
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
104097
104098
104160
165100
165373
177041
177048
177057
193943
194013
194392
DVX-30
DVX-31
170244
170245
Item
104156 - Ram Unit Parts Lists
Part No. Description Qty. Remarks
77-3237 R3.0 (06/2025) 16/32 www.binks.com
EN
104156 - Ram Unit Assembly
77-3237 R3.0 (06/2025) 17/32 www.binks.com
EN
DRX205
104157 - Installation
The ram plate base should be mounted on a stable and level floor.
The standard ram plate has 4 off - holes Ø21mm to enable the base to be securely fixed to the floor.
Suitable floor fixing ‘rawlbolts’ should be used which are designed to suit the floor material.
Base plate = 1150mm x 680mm. Mounting holes = 1290mm x 600mm
A compressed air supply is connected to the ½ BSP F connection to control the lift and lowering of the air
cylinders and supply the pump.
77-3237 R3.0 (06/2025) 18/32 www.binks.com
EN
1
1
1
DR205 Ram Unit Outfit Assemblies
1
3
5
104157
194000
194465
MX200 MODELS
MX115 MODELS
DRX205E RAM ASSEMBLY
CONNECTION KIT – NOT SHOWN
CONNECTION KIT – NOT SHOWN
Item Part No. Description Qty. Remarks
2 MX…… PUMP ASSEMBLY – SEE SELECTION TABLE 1
MX420/860 MODELS1CONNECTION KIT – NOT SHOWN1940014
DR205 Ram Unit Outfit Parts List
77-3237 R3.0 (06/2025) 19/32 www.binks.com
EN
1
1
1
2
2
2
1
1
4
1
2
2
1
1
4
4
3m
2m
NOT SHOWN
NOT SHOWN
RemarksQty.
RAM CONTROL BOX
RAM AIR REG SETUP
DRX TRIP ROD KIT
M16 SPRING WASHER
M20 SPRING WASHER
M16 x 70 HEX HED BOLT
M20 HEX NUT - PLATED
M20 STUD CONNECTOR
M4 x 45 SOCKET HD CAP SCREW
SUPPORT BAR
¼ - Ø6 PUSH IN ELBOW
DRUM STOP
205L FOLLOWER PLATE ASSEMBLY
DRX205 BARE RAM UNIT
M4 NYLOC NUT
M4 WASHER
Ø6 x 4 PU HOSE - BLACK
Ø4 x 2.5 PU HOSE - BLACK
Description
10
11
12
13
14
15
16
17
18
Item
104097
104098
104160
165100
165139
165373
177034
177035
177041
193765
193943
194013
194295
194393
DVX-30
DVX-31
170244
170245
Part No.
104157 - Ram Unit Parts List
2
1
3
4
5
6
7
8
9
77-3237 R3.0 (06/2025) 20/32 www.binks.com
EN
104157 - Ram Unit Assembly
77-3237 R3.0 (06/2025) 21/32 www.binks.com
EN
104097 - Ram Control Box Details
WHEN LINKED TO AUTOCHANGEOVER
D = DRUM EMPTY SIGNAL
E = PUMP START SIGNAL
A = MAINS AIR TO TRIP ROD
B = TRIP ROD SIGNAL
C = PUMP SHUT OFF SIGNAL
Ø4mm PUSH IN
START
PUMP
RAM
UP/DOWN
RAM FORCE
GUAGE
RAM FORCE
REGULATOR
STOP
PUMP
DRUM
RELEASE
PUMP STATUS
INDICATOR
(GREEN=ON / RED=OFF)
Ø6mm PUSH IN
1 = MAINS AIR INLET
2 = RAM UP
3 = RAM DOWN
4 = DRUM RELEASE
77-3237 R3.0 (06/2025) 22/32 www.binks.com
EN
104098 - Air Regulator Unit
PUMP STOP
PILOT SIGNAL FROM
CONTROL BOX(C)
½ OUTLET
TO PUMP
PUMP STOP
SILENCER
PILOT OPERATED
SHUT OFF VALVE
FILTER BOWL
5 MICRON½ INLET
BALL VALVE
MAINS AIR TO
CONTROL BOX (1)
PUMP AIR
PRESSURE GAUGE
INCOMING AIR
SAFETY VALVE – 8 BAR
PUMP AIR
REGULATOR
77-3237 R3.0 (06/2025) 23/32 www.binks.com
EN
104160 - Trip Rod Parts List
104160 - Trip Rod Assembly
# - Recommended spares for 104160
Remarks
M6 NYLOC NUT
M6 x 20 CAP HD SCREW
M6 WASHER
M6 x 16 BUTTON HEAD SCREW
M6 x 50 SOCKET HD CAPSCREW
VENT PLUG
TRIP ROD ASSEMBLY
TRIP ROD 3/2 VALVE
⅛ - Ø4 PUSH IN ELBOW
VALVE BRACKET
DRX TRIP ROD CLAMP
M4 x 25 CAP HEAD SCREW
M4 NYLOC NUT
M4 WASHER
Description
13
14
Item Part No.
0115-010211
163952
165129
177031
177066
192799
193902
193907
193908
194474
194475
DVX-27
DVX-30
DVX-31
2
1
3
4
5
6
7
8
9
10
11
12
#
77-3237 R3.0 (06/2025) 24/32 www.binks.com
EN
4
1
1
1
1
1
2
2
194461 - Ram Plate 60L / 15G Parts List
194461 - Ram Plate 60L / 15G Assembly
¼ NON RETURN VALVE
¼ - Ø6 PUSH IN STRAIGHT
¼ MALE - ¼ MALE NIPPLE
DRX60 FOLLOWER PLATE MACHINING
¾ STRAPPING - 1.3m LONG
WIPER SEAL - EPDM
Description
2
1
3
4
5
6
7
8
Item
181672
193754
193768
193769
193948
194297
194466
194467
Part No. RemarksQty.
¾ STRAP BUCKLE
PRIMER SCREW ASSEMBLY
77-3237 R3.0 (06/2025) 25/32 www.binks.com
EN
4
1
1
1
1
1
1
1
2
1
2
194295 - Ram Plate 205L / 55G Assembly
194295 - Ram Plate 205L / 55G Parts List
6 193946 ½ MALE - ½ FEMALE ELBOW
7 193948 ¼ MALE - ¼ MALE NIPPLE
8 194296 ¾ PLUG
202522
205027
207064
¾ STRAPPING - 2.3m LONG
205L RAM PLATE MACHINING
RAM SEAL
9
10
11
1 181672 ¾ STRAP BUCKLE
2 193768 ¼ NON RETURN VALVE
3 193769 ¼ - Ø6 PUSH IN STRAIGHT
4 193944 ½ PLATED BRASS BALL VALVE
5 193945 ½ BSPT - ½ BSPT NIPPLE
Item Part No. Description Qty. Remarks
DETAIL A
SCALE 1 : 5
77-3237 R3.0 (06/2025) 26/32 www.binks.com
EN
Accessories
Water Based – 0.5L
Solvent Based – 0.5L
0114-014883 – 100 Mesh
0114-014882 – 150 Mesh
0114-014881 – 200 Mesh
191833 – 200 Micron Element St St
191834 – 400 Micron Element St St
192523 – 600 Micron Element St St
192524 – 1200 Micron Element St St
Filter Element to be Specified Separately
Filter Element to be Specified Separately
Twin Filter Housing Assembly
Carbon St
Twin Filter Housing Assembly
St St
Filter Housing St St
Filter Housing Carbon St
Item Part No.
10787712
10787611
1078669
To Automatically change over to a Standby
Ram Unit when the Duty Ram Unit is empty
(Bottom Position)
Auto Change Over Panel
Description Remarks
1040991
0110-009131 – 50 Mesh
0110-009133 – 150 Mesh
0110-009134 – 200 Mesh
0114-014917 – 30 Mesh
0114-014886 – 50 Mesh
0114-014884 – 70 Mesh
High Pressure Filter (100
Mesh)
0110-0091302
High Pressure Filter
(100 Mesh)
(500 bar Max.)
3 0114-011760
Water Based – 0.25L
Solvent Based – 0.25L
5
6
7
8
10
0114-016099
0114-016100
0114-014871
0114-009433
107867
Pump Lubrication
Pump Lubrication
Pump Lubrication
Pump Lubrication
77-3237 R3.0 (06/2025) 27/32 www.binks.com
EN
2
2
4
1
1
2
3m
2m
1
2
2
4
1
1
2
1
3m
2m
1
9
8
7
6
5
4
3
2
1
4 250725 Ram Cylinder Seal Kit 2 1 Per Cylinder
1 Per Cylinder2Ram Cylinder Seal Kit25072510
193948
170244
170245
Item Part No. Description Qty Remarks
# Spare Parts For - 104160 Trip Valve Kit
RemarksQtyDescription
3/2 Trip Valve193907
Part No.Item
1
Wiper Seal - EPDM
Strapping
Strap buckle
¼ Non Return Valve
¼ – Ø6 Push In Straight
¼ – Ø6 Push In Elbow
¼ Male – ¼ Male Nipple
Ø6 x 4 PU Hose – Black
Ø4 x 2.5 PU Hose - Black
207064
202522
181672
193768
193769
# Spare Parts For – (DRX205) 104157 Ram Unit
193943
170245
193948
1
2
3
5
6
7
8
9
10
Wiper Seal - EPDM
Strapping
193769
193943
170244
¼ – Ø6 Push In Elbow
Ø6 x 4 PU Hose – Black
¼ Male – ¼ Male Nipple
Description Qty Remarks
# Spare Parts For – (DRX60) 104156 Ram Unit
Item Part No.
Ø4 x 2.5 PU Hose - Black
Strap buckle
¼ Non Return Valve
¼ – Ø6 Push In Straight
194467
194466
181672
193768
77-3237 R3.0 (06/2025) 28/32 www.binks.com
EN
CYLINDER ROD HOUSING ASSEMBLY
RAM PISTON
Cylinder Service Reference – Spares Kit 250725
77-3237 R3.0 (06/2025) 29/32 www.binks.com
EN
RAM SHAFT
GREASE - (AGMD-010)
GREASE INTERNAL
(AGMD-010)
RAM PISTON
TIGHTEN TO 50 Nm
77-3237 R3.0 (06/2025) 30/32 www.binks.com
EN
WARRANTY POLICY
This product is covered by Binks materials and workmanship limited warranty.
The use of any parts or accessories, from a source other than Binks, will void all
warranties. Failure to reasonably follow any maintenance guidance provided, may
invalidate any warranty.
For specific warranty information please contact Binks.
For technical assistance or to locate an authorised distributor, contact one of our
international sales and customer support locations below.
REGION BINKS CONTACT
Americas Tel: 1-888-992-4657
Europe, Africa, Middle East Tel: +44 (0)1202 571 111
India marketingroa@binks.com
China Tel: +8621-3373 0108
Korea Tel: +82313663303
Japan Tel: +81 45 785 6421
Australia Tel: +61 (0) 2 8525 7555
WARRANTY PAGE
77-3237 R3.0 (06/2025) 31/32 www.binks.com
EN
© 2025 Binks US, LLC. All rights reserved.
Binks is a global leader in innovative finishing technologies. Binks reserves the right to modify
equipment specifications without prior notice.
Binks®, DeVilbiss®, and Ransburg® are registered trademarks of Binks US, LLC.
77-3237 R3.0 (06/2025) 32/32 www.binks.com
