Resource Library
Trochoid Pump Unit Manual
- Trochoid Pump Uniti Manual [ English ]
ENG 5A 00B V 002
This manual explains the important information and warnings.
Please read carefully and follow the instructions.
Trochoid Pump Unit
5A00000B
New, 25 Apr. 2017
Revision, 21 May. 2019
Warnings and Cautions p. 3 ~ 4
Specification & Performance p. 5 ~ 8
Installation p. 9 ~ 10
Trouble Shooting p. 11
Overhauling p. 12 ~ 19
Option p. 19
Maintenance and RPK Kit p. 20
Dimensions p. 21
Parts List p. 22 ~ 25
Standard Warranty p. 26
Table of Contents
Trochoid Pump Unit
5A00000B
Page2
WARNING CAUTION
This symbol means the possibility of This symbol means the possibility of
serious injury or death if you ignore damage or destruction of equipment
the instructions. if you ignore the instructions.
HAZARD OF EQUIPMENT MISUSE
Equipment misuse may provoke its malfunction, rupture or unexpected start and result in
a serious injury.
■ This equipment is for professional use only.
■ Read all instructions in manual, tags and labels carefully before operation.
■ Use this equipment for specified purpose. If not, inquire to Binks.
■ Do not remodel or modify this equipment.
■ Use the genuine parts and accessories from Binks.
■ Do daily check for the equipment. The worn or damaged part should be repaired or
replaced with new one.
■ Do not exceed the maximum pressure of parts or accessories.
■ Route the hoses or cables away from traffic areas, sharp edges, moving parts and hot
surfaces.
■ Do not twist, bend and pull the hoses and cables arbitrarily.
■ Read the MSDS of material and follow it.
■ Wear the earplug when operating this equipment with RAM pump.
■ Wear the protecting gears like goggles, gloves, mask and suits recommended by the
manufacturer of material.
■ Comply with the local regulations about fire, electric and safety.
WARNING
WARNING and CAUTION
Trochoid Pump Unit
5A00000B
Page3
HAZARD FROM THE HIGH PRESSRE EQUIPMENT
The leak of hoses or the rupture of parts can inject high pressure fluid to your skin or eyes
and result in serious injuries.
■ Check hoses, tubes and fittings daily. The worn, damaged or loosened parts should be
replaced with new one immediately.
■ Check bolts and nuts weekly and fasten the loosened one.
HAZARD FROM FIRE OR EXPLOSION
As not being ventilated, flame or sparks can cause fire or explosion.
■ Keep the shop ventilated to prevent from accumulating flammable or toxic gas.
■ Isolate all equipment from electric sources.
■ Remove all flammable material and keep the shop clean.
■ Do not smoke at the shop.
HAZARD FROM TOXIC MATERIAL
If your eyes or skin are exposed to toxic materials, serious damages or death can be
resulted.
■ Wear the protecting gears like goggles, gloves, mask and suits recommended by the
manufacturer of material.
WARNING
Trochoid Pump Unit
5A00000B
Page4
This trochoid pump is optimized to be used just for high viscous materials but can be
used for various fluids.
The performance and the efficiency of pump may be decreased slightly in the low
pressure and the low viscous condition.
■ Design information
This trochoid pump is called as Gearotor pump, has trochoidal gearing and the profile
of its rotors are the Epi-trochoid curve.
Rotor hous'g, inner rotor and outer rotor of this pump got precision-made and inner
rotor has 6 teeth, outer rotor 7 teeth and its displacement per revolution is 26 cm³.
This trochoid pump is designed for high pressure and/or high viscosity.
Under high pressure operation, its inner and outer rotor are free from axial forces
and thus keep very smooth running and, low noise generation and best quality.
SPECIFICATION & PERFORMANCE
Displacement = 26cc/rev
Idler
Rotor
Trochoid Pump Unit
5A00000B
Page5
■ Specification
The performance of Trochoid pump for high viscous material is defined as the
differences of pressure (Δp) between inlet and outlet.
Max. (Δp) 300 kgf/cm² (bar)
Recommendable (Δp) 100 kgf/cm² (bar)
Displacement 26 (cc/rev)
* Allowable input torque 250 Nm
■ Performance Chart * This chart is restricted to the specified test condition.
350
400
450
500
550
600
650
700
750
-100 -50 0 50 100 150 200 250
ΔPout-in (bar)
Discharge amount
(gpm) ±10%
Test Condition
Reducing ratio 1/21, Servo motor 400rpm
Material : BPR Sealer (900,000 cps)
Test temperature : 24~30°C
Max. Continous working time is within 2min.
Theoretical discharge amount is 594 rpm.
* Practical discharge amount is proportional to the rpm of motor.
Trochoid Pump Unit
5A00000B
Page6
To calculate the discharge volume(ccpm) or gpm(gram/min) :
1) In the case of direct driving pump by motor,
ccpm(cc/min) = 26 (cc) x rpm(motor)
gpm(gram/min) = 26 (cc) x rpm(motor) x ν(specific gravity)
2) In the case of using reducer,
ccpm(cc/min) = 26 (cc) x rpm(motor)
ψ(reducing ratio)
gpm(gram/min) = 26 (cc) x rpm(motor) x ν(specific gravity)
ψ(reducing ratio)
ex 1) Calculate discharge volume per minute when motor rpm is 400.
Discharge volume (ccpm) = 26 x 400
= 10,400 cc/min
= 10.4 ℓ/min
ex 2) Calculate discharge weight when motor rpm is 400, reducing ratio 20
and specific gravity of fluid is 1.2.
Discharge weight (gpm) = ( 26 x 400 x 1.2 ) / 20
= 624 g/min
Notice!
* The above chart is restricted to the specified test condition and thus the discharge volume is affected
by not only the viscosity of material (including temperature), but also the differences of pressure(Δp).
* The lower the viscosity and the higher the pressure differences are, the less the discharge volume
can be than theoretical calculation because of inner circulation.
■ Reference table for calculation of the discharge volume per minute(ccpm, gpm)
Theoretical displacement per a revolution = 26 cc/rev
ccpm gpm
10 x N *210 260 ν x 260 N : reducing ratio
20 x N *420 520 ν x 520 ν : specific weight
30 x N *630 780 ν x 780
40 x N *840 1040 ν x 1040
50 x N *1050 1300 ν x 1300
60 x N *1260 1560 ν x 1560
Asterisk(*) is the servo motor rpm when reducing ratio is 21 as an example.
30
40
50
60
Servo motor rpm Trochoid pump rpm
10
20
Trochoid Pump Unit
5A00000B
Page7
■ Use for :
This Trochoid pump developed for high pressure, high viscous material is machined
and assembled precisely and thus achieve saving energy, very smooth running, low
noise generation and also good suction capability in low viscous fluid under 500,000cps.
Therefore, this pump can be useful for the followings.
Refer the following chart about viscosity of material.
viscosity
(cps)
viscosity
(cps)
* cps : centi-poise
240,000 100 1 Ps = 100 cps
45,000 88 1 Pa.s = 1,000 cps
38,000 77 cst : centi-stroke
30,000 65 cps = ν x cst
25,000 15 (ν : specific weight)
18,000 11.6
12,000 10
8,000 5.3
6,000 4,4
2,000 2.5
1,800 2,0
1,300 1.22
1,000 1.19
1,000 1
high pressure &
high viscous material
Automobile industry
(Body & Powertrain)
material material
sodium silicate(20℃) dynamo oil(20℃)
pomade(21℃) frying oil(18℃)
above 500,000 cps
(sealing/painting/hemmi
ng/bonding system)
low pressure &
low viscous material
Pharmaceutical Industry less than 500,000 cps
(Pumping/transferring/m
etering)
Cosmetic industry
Food industry
Oil & Chemical industry
cold cream(23℃) phenol(20℃)
shoe polish(20℃) kerosene oil(20℃)
mayonnaise(23℃) soy sauce(17℃)
chocolate topping(21℃) tomato juice(24℃)
tooth paste(21℃) salad oil(23,5℃)
cylinder oil(20℃) glycerin(20℃)
honey(21℃) acetic acid(20℃)
castor oil(20℃) ethyl alcohol(20℃)
asphalt(20℃) water(20℃)
strawberry jam(23℃) aniline(20℃)
condensed milk(21.5℃) milk(15℃)
ketchup(24℃) nitro benzene(20℃)
Trochoid Pump Unit
5A00000B
Page8
This procedure is for installation of the Trochoid pump unit.
Install this equipment according to the instruction and the applicable safety rule.
If you need more information, inquire to Binks.
■ The standard model of this trochoid pump has a single feather key at its shaft.
■ Refer the following dimension to design an equipment or system using this Trochoid
pump.
* The allowable input torque of standard model among this Trochoid pump is 250 Nm.
■ The bracket of Binks is recommended for installation.
INSTALLATION
shaft
Key
BRACKET,
This is not a standard part but
made by the customer's order
Trochoid Pump Unit
5A00000B
Page9
■ The flexible coupling is recommendable for connecting with motor and reducer.
Rigid connection can cause to mismatch their centers between two shafts of motor and pump.
That results in damage of Trochoid pump.
■ The flatness of stand should keep less than ±0.5mm
■ Check the inlet and outlet of Trochoid pump and connect specified fittings(PT3/4).
■ Connect the drain v/v ass'y to fittings and then connect the hoses to them.
* In some case, the drain v/v can be deleted.
* In some case, the shut off v/v and the ball v/v can be added.
This image show a kind of the metering unit applied with the trochoid pump.
Motor Reducer Trochoid pump
Flexible coupling
Trochoid Pump Unit
5A00000B
Page10
(Servo) motor jammed Repair or exchange
Trochoid pump blocked Repair or exchange
Fluid hardened Check temperature and overhaul
Troubles Causes Solution
Not discharging fluid Power off Check power line and recover.
Primary pump blocking Check and recover
Elec. Connector contaminated Remove and recover
Mechanical noises (Servo) motor failure Exchange
Trochoid pump failure Repair or exchange
Reducer failure Repair and lubricate
TROUBLE SHOOTING
Trochoid Pump Unit
5A00000B
Page11
1. Disassembling Trochoid pump
Notice!
* Use the specified tools and do not overload to prevent from deformation.
Prepare the specified repair kits before overhauling.
■ Disconnect the fluid hose/fitting of inlet and outlet.
■ Disconnect the flexible coupling between the motor and Trochoid pump.
■ Loosen 6 Wrench Bolts (M12) of Mt'g brkt by Zigzag way and dismantle the Trochoid pump.
■ Remove the feather key ⓑ from shaft.
■ Loosen 6-M12 bolts ⓐ by Zigzag way.
■ Loosen set screw ⑥ and then Cap nut-front ⑤.
■ Extract 'Sub ass'y-Packing Nut' ③ from 'Front Body ass'y' ②.
■ Separate 'Sub ass'y-Front Body' ② and 'Sub ass'y-RR body' ④ from 'Sub ass'y-Main' ①.
OVERHAULING
wrench bolt
BRKT-MT'G
TROCHOID PUMP
ⓑ
ⓐ
⑤
⑥
③
①
②
④
Trochoid Pump Unit
5A00000B
Page12
■ To disassemble 'Sub ass'y-Packing Nut' like the figure ;
- Remove O-ring ⓓ.
- Extract Bearing ⓒ, O-ring ⓑ and U-packing ⓐ by bare hands.
- Dip Packing nut ① in a washer like a thinner in order to remove the hardened or pasted
material.
- Cleanse Packing nut ① with bronze wire brush and get it greased.
- Cleanse Bearing ⓒ and get it greased.
- Check Packing nut ① and Bearing ⓒ whether or not damaged.
If damaged, take its photo and inquire to Binks by e-mail.
- Check U-packing ⓐ and O-ring ⓑ whether or not damaged.
If damaged or deformed, take its photo and inquire to Binks by e-mail.
Notice!
* In high pressure operation, U-packing ⓐ may show a heavy one-side wear.
If leaked before overhaling, inquire to Binks by e-mail.
ⓐ
ⓓ
①
ⓑ ⓒ
Trochoid Pump Unit
5A00000B
Page13
■ To disassemble 'Sub ass'y-FRT Body' like the figure ;
- Extract Packing Washer ② and U-Packing ⓐ by bare hands.
- Remove O-Ring ⓑ and ⓒ by bare hands.
- Dip Frt body ① and Packing washer ② in a washer like a thinner in order to remove the
hardened or pasted material.
- Cleanse Frt body ① and Packing washer ② with a bronze wire brush and get them greased.
- Check Frt body ① and Packing washer ② whether or not damaged.
If damaged, take its photo and inquire to Binks by e-mail.
- Check U-packing ⓐ, O-ring ⓑ and ⓒ whether or not damaged.
If damaged or deformed, take its photo and inquire to Binks by e-mail.
Notice!
* In high pressure operation, FRT Body ①, Packing Washer ②, U-Packing ⓐ and O-Ring ⓒ may show
a heavy one-side wear.
If leaked before overhaling, inquire to Binks by e-mail.
ⓑ
ⓒ
①
ⓐ ②
Trochoid Pump Unit
5A00000B
Page14
■ To disassemble 'Sub ass'y-RR Body' like the figure ;
- Extract O-ring ⓑ, Packing washer ④ and U-packing ⓐ by bare hands.
- Loosen Cap nut ② with monkey spanner and separate.
- Extract Bearing ⓓ, O-ring case ③ by bare hands.
- Remove O-ring ⓒ from O-ring case ③ by bare hands.
- Dip Rr body ①, packing washer ④, O-ring case ③ and cap nut ② in a washer like a thinner
in order to remove the hardened or pasted material.
- Cleanse Rr body ①, Packing washer ④, O-ring case ③ and Cap nut ② with a bronze wire
brush and get them greased.
- Cleanse Bearing ⓓ and get it greased.
- Check Rr body ① and Packing washer ④ whether or not damaged.
If damaged, take its photo and inquire to Binks by e-mail.
- Check U-packing ⓐ and O-ring ⓒ whether or not damaged.
If damaged or deformed, take its photo and inquire to Binks by e-mail.
Notice!
* In high pressure operation, Rr body ①, Packing washer ④, U-packing ⓐ and O-ring ⓒ may show
a heavy one-side wear.
If leaked before overhaling, inquire to Binks by e-mail.
①
ⓓ
ⓒ ③
①
ⓑ
ⓐ ④
Trochoid Pump Unit
5A00000B
Page15
■ To disassemble 'Sub ass'y-Main' like figure ;
- Extract 2 Dowel Pins ⓓ with rod (Φ9 L60) and a rubber hammer.
- Locate rod on Dowel Pin ⓓ and strike it with snaps by a rubber hammer till being extracted
out.
- Separate FRT Guide ⑥ and RR Guide ① from Housing ②.
- Extract U-Packing ⓐ and O-Ring ⓒ from Housing ① by bare hands.
- Remove O-Rings ⓑ from Housing ② by bare hands.
- Extract Shaft ⑤, Rotor ④ and Idler ③ carefully from Housing ② by bare hands.
- Dip RR Guide ①, Housing ②, FRT Guide ⑥, Idle ③, Rotor ④, Dowel Pins ⓓ and Shaft
⑤ in a washer like a thinner in order to remove the hardened or pasted material.
- Cleanse RR guide ①, Housing ②, FRT Guide ⑥, Idler ③, Rotor ④, Dowel Pins ⓓ and Shaft
⑤ with a bronze wire brush and then get them greased.
- Check them whether or not damaged, scuffed or scratched.
If damaged, peeled or cracked, take its photos and inquire to Binks by e-mail.
- Check U-Packing ⓐ, O-Ring ⓒ whether or not damaged.
If damaged or deformed, take its photos and inquire to Binks by e-mail.
Notice!
* In high pressure operation, RR Guide ① and Idler ③ may get scratched each other.
And Shaft ⑤, FRT Guide ⑥ and RR Guide ① may get scratched each other.
And U-Packing ⓐ and O-Ring ⓒ may show a heavy one-side wear or damaged.
If leaked before overhaling, inquire to Binks by e-mail.
ⓐ ⓒ
①
ⓑ
②
ⓑ
③
④
⑥ ⓓ
⑤
Trochoid Pump Unit
5A00000B
Page16
2. Reassembling Unit
Reassembling should be accomplished in reverse order.
Use the specified tools and apply the designated torque to fasten bolts and nuts.
Replace U-packing, O-ring and packing washer with new one (repair kit).
■ To assemble 'Sub ass'y-Main' in reverse order of disassembling by bare hands ;
- Combine Housing, Idler and Rotor.
- Insert Shaft into Rotor carefully.
- Paste grease to 2 O-rings and locate them at Housing by bare hands.
- Paste grease to O-Ring and U-Packing, and insert them into RR Guide by bare hands.
- Combine RR Guide and FRT Guide to Housing through Shaft, and allign the furrow mark on
their surfaces.
- Locate 2 Dowel Pins into the hole of FRT Guide and strike them alternately with snaps by
a rubber or plastic hammer.
☞ Refer to page 16.
Notice!
* When inserting 2 Dowel pins, do not strike them forcedly. It can makes pins carved and their scraps
damages Frt & Rr guide and Housing.
■ Assemble 'Sub ass'y-FRT Body' in reverse order of disassembling by bare hands.
- Before reassembling, paste grease enough to U-packing and O-Ring.
☞ Refer to page 14.
■ Assemble 'Sub ass'y-RR Body' in reverse order of disassembling by bare hands and spanner.
- Before reassembling, paste grease enough to U-Packing, O-Ring, Packing Washer and
Bearing.
- Insert U-Packing, O-Ring Case including O-Ring, Packing Washer and Bearing by bare hands.
- Fasten Cap Nut tightly with a monkey spanner.
☞ Refer to page 15.
snap
motion
Trochoid Pump Unit
5A00000B
Page17
■ Assemble 'Sub ass'y-Packing Nut' in reverse order of disassembling by bare hands.
- Before reassembling, paste grease enough to U-Packing, O-Ring and Bearing.
- Insert U-Packing, O-Ring and Bearing into Packing Nut.
- Insert snap ring by a plier.
☞ Refer to page 13.
■ Complete the assembly of Trochoid pump by bare hands.
- Combine 'Sub ass'y-FRT Body' and 'Sub ass'y-RR body' to 'Sub ass'y-Main'.
Before combining, confirm O-Ring and the direction of U-Packing.
Combine them vertically and rotate Shaft by hand to balance its center itself.
- Insert 6 Wrench Bolts (M12 L95), confirm the match of furrow mark and then fasten them by
Zigzag tightening. Keep fastening torque 77 Nm.
☞ Refer to page 12.
Notice!
* After finishing to reassemble, check carefully rotating by a proper tool. If feeling or listening a mechanical
friction, overhaul again because of including other matters like metal debris or things like that.
Notice!
* Keep the direction of U-Packings.
Trochoid Pump Unit
5A00000B
Page18
Generally the high viscous fluid is sensitive to temperature and therefore its viscosity goes
down rapidly as its temperature become higher.
In circumstance of high viscous fluid, the HEATING BLOCK can be chosen in order to
make pumping easy.
Heater & Sensor Pin Connection no.
Pin no. Q'ty
1 1
2 1
3 1
4 1
5 1
6 1
7 1
Description
Sensor(-)
Sensor(-)
Sensor(+)
dummy
dummy
Heater
Heater
OPTION
Heating Block ass'y
(for Trochoid pump)
0Z05100A
Trochoid
pump
Heating
Block ass'y
Trochoid Pump Unit
5A00000B
Page19
Maintenance is important for the best performance and the life of the equipment.
This maintenance shown here is the general procedure and the condition of operation
is dependent on the material, operating period, the circumstances of shop and so on.
Therefore, every cases of operation can not be offered the warranty.
It is recommended to consider user's experiences and the circumstances of shop in
order to decide the overhaul period.
The following check table describes about an equipment including Trochoid pump.
■ Daily Check
■ Monthly Check
■ Lubrication
It is recommended to be lubricated annually (when being overhauled).
■ RPK
P/NO Q'ty KIT no
M1301 2
M3101 4
M3203 2
M3201 4
M3202 2
M3285 1
Acoustic test (servo) motor
metallically frictional sounds,
clacking noises
Stop to operate.
Inquire to Binks.
reducer
trochoid pump
shut off v/v
air leaking sounds
Remove causes and
repair.sol. v/v
UNIT P/NAME
wetness and contamination Cleansing
pressure gauge abnormal operation Exchange
hoses and cables damages or contamination Exchange or cleansing
Visual test trochoid pump
leaking of fluid
contamination
Inquire to Binks.
shut off v/v Repair with RPK or
overhaulball v/v
elec. Connector
Mechanical test bolts and nuts
loosened Fastening
fittings
Trochoid pump (26cc/rev)
5A00000B
Bearing
5ARK0004
U-packing
O-ring
O-ring
O-ring
O-ring
MAINTENANCE and REPAIR KIT(RPK)
Trochoid Pump Unit
5A00000B
Page20
DIMMENSIONS
Trochoid Pump Unit
5A00000B
Page21
PARTS LIST
Trochoid Pump Unit
5A00000B
Page22
P/no Q'ty
① 5A40002A 1
② 5A40003A 1
③ 5A40001A 1
④ 5A20002A 2
⑤ 5A10001A 1
⑥ 5A10004A 1
⑦ 5A10003A 1
⑧ 5A10005A 1
⑨ 5A10002A 1
⑩ 5A10006A 1
⑪ 5A20001B 1
⑫ 5A30001B 1
⑬ 5A30002B 1
ⓐ M1301 2
ⓑ M3203 2 RPK
ⓒ Q1301 6
ⓓ M3101 4 RPK
ⓔ M3201 4 RPK
ⓕ M3202 2 RPK
ⓖ M3285 1 RPK
ⓗ Q1611 3
ⓘ M2201 1
ⓙ Q4101 2
Description remark
CAP NUT, rear
O-RING CASE
RR BODY
PACK'G WASHER
FRT BODY
PACKING CASE
CAP NUT, front
BEARING
O-RING
WRENCH BOLT & S/W
RR GUIDE
ROTOR
IDLER
SHAFT
HOUSING
FRT GUIDE
DOWEL PIN
U-PACK'G
O-RING
O-RING
O-RING
SET SCREW
KEY
PARTS LIST
Trochoid Pump Unit
5A00000B
Page23
PARTS LIST (OPTION)
Heating Block
Connector
BRKT
Connector
②
⑦
⑧
⑧
⑨
ⓐ
ⓑ
①
③
④
③
⑤
⑥
ⓖ
ⓖ
ⓗ
ⓒ
ⓓ
ⓔ
ⓕ
Trochoid Pump Unit
5A00000B
Page24
P/no Q'ty
① 0Z05101A 1
② 0Z05102A 1
③ 0Z05103A 2
④ 0Z05104A 1
⑤ 0Z05105A 1
⑥ 0Z05106A 1
⑦ 0Z05107A 1
⑧ 0Z05108A 2
⑨ 0Z05109A 1
ⓐ Q1357 2
ⓑ Q1308 28
ⓒ E2101+E2102 1
ⓓ Q1306 4
ⓔ E7206 1
ⓕ E6101 1
ⓖ Q1607 2
ⓗ Q1623 2
Description remark
Heating Block material : AL
Connector BRKT material : AL
Top Cover material : BAKELITE
Connector BRKT, FRT Cover material : BAKELITE
Connector BRKT, SIDE Cover material : BAKELITE
Front Cover material : BAKELITE
Side Cover, LH material : BAKELITE
Side Cover, RH material : BAKELITE
Connector
Wrench Bolt & S/W
Cartridge Heater
Connector BRKT, BOTTOM Cover material : BAKELITE
Wrench Bolt & S/W
Round Headed (+) Screw
Heater Sensor
Set Screw
Set Screw
PARTS LIST (OPTION)
Trochoid Pump Unit
5A00000B
Page25
Binks warrants all equipment manufactured by Binks to be free from defects in material and
workmanship on the date of sale to original purchaser for use. With the exception of any special, extended,
or limited warranty published by Binks, Binks will, for a period of 12 months from date of sale, repair
or replace any part of equipment determined by Binks to be defective. This warranty applies only when
the equipment is installed, operated and maintained in accordance with Binks's written recommendations.
This warranty does not cover, and Binks shall not be liable for general wear and tear, or any malfunction,
damage or wear caused by faulty installation, misapplication, inadequate maintenance, negligence, accident,
tampering, or substitution of non-Binks component parts. Nor shall Binks be liable for malfunction,
damage or wear caused by the incompatibility of Binks equipment with structures, accessories,
equipment or materials not supplied by Binks, or improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Binks.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an
authorized Binks distributor for verification of the claimed defect. If the claimed defect is verified,
Binks will repair or replace free of charge any defective parts. The equipment will be returned to the
original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in
material or workmanship, repairs will be made at a reasonable charge, which charges may include the cost
of parts, labor, and transportation.
This warranty is exclusive, and is in lieu of any other warranties, express or
implied, including but not limited to warranty of merchantability or warranty
of fitness for a particular purpose.
Binks's sole obligation and buyer's sole remedy for any breach of warranty shall be as set forth above.
The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages
for lost profits, lost sales, injury to personal property, or any other incidental or consequential loss) shall be
available. Any action for breach of warranty must be brought within (2) years of the date of sale.
Binks makes no warranty, and disclaims all implied warranties of merchantability and fitness for a
particular purpose in connection with accessories, equipment, materials or components sold but not
manufactured by Binks. The items sold, but not manufactured by Binks like electric motor, switches,
reducers, bearings and so on, are subject to warranty, if any, of their manufacturer. Binks will provide
purchaser with reasonable assistance in making any claims for breach of these warranties.
In no event will Binks be liable for indirect, incidental, special or consequential damages resulting from
Binks supplying equipment hereunder, or the furnishing, performance or use of any product or other
goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Binks, or
otherwise.
STANDARD WARRANTY
Trochoid Pump Unit
5A00000B
Page26
MEMO
Trochoid Pump Unit
5A00000B
Page27
