- Maple Pump 3/36 Manual 77-3341 EN [ English ]
77-3341
Maple 3/36
Pump
104267
EN
It is the Customer's responsibility to have all operators and service personnel read and
understand this manual.
Contact your local Binks representative for additional copies of this manual.
READ ALL INSTRUCTIONS BEFORE OPERATING THIS PRODUCT
ADDITIONAL RESOURCES
For additional information or copies of your service manual, please visit us online at:
binks.com/en/library
Or use this QR code with your mobile device:
XXXXXXXX
Insert
QR
code
Obey local or municipal regulations for product recycling and disposal.
IMPORTANT! DO NOT DESTROY
77-3341 R2.1 (04/2025) 2/28 www.binks.com
EN
Pumps - Maple, DVP, 104009, 104010/LS, 104016, 104027,
104032, 104040/1/2, 104077, 104020-M2, 104023, 104025,
104028/9, 106933, 104205,104149-52, 104207-15, 104147,
104265/66/67.
Suitable for use in hazardous area: Zone 1/Zone 2
Protection Level: Ex h IIB T4 Gb X
Notified body details and role: Element Materials Technology Rotterdam B.V. (2812)
Lodging of ATEX Technical file
Providing all conditions of safe use / installation stated within the product manuals have been complied with and also installed in accordance
with any applicable local codes of practice.
Signed for and on behalf of Binks
U.K. Ltd:
Executive President: Engineering and
Operations, Shoreview, MN, 55126. USA
Machinery Directive 2006/42/EC
ATEX Directive 2014/34/EU
by complying with the following statutory documents and harmonised standards:
EN ISO 12100:2010 Safety of Machinery - General Principles for Design
EN 12621:2006+2010 Machinery for the supply and circulation of coating materials under pressure - Safety requirements
EN ISO 80079-36:2016 Explosive Atmospheres- Part 36:Non Electrical equipment for explosive atmospheres-Basic methods
and requirements.
EN ISO 80079-37:2016 Explosive Atmospheres- Part 37: Non Electrical equipment for explosive atmospheres - protection by
methods c, b and k.
EN 1127-1:2019 Explosive atmospheres - Explosion prevention - Basic concepts
22/04/25
Product Description / Object of Declaration:
This Product is designed for use with: Solvent & Waterbased Materials
This Declaration of Conformity / Incorporation is issued
under the sole responsibility of the manufacturer:
Binks U.K. Limited,
Ringwood Road,
Bournemouth, BH11 9LH. UK
Representative authorised to compile the technical file President @. Binks France SAS
5 Place Pierre Semard, 94130 Nogent sur Marne , Paris, France
EU Declaration of Conformity
This Declaration of Conformity / Incorporation is issued under the sole responsibility of the
manufacturer:
Document Part No.
.
F. A. Sutter
77-3341 R2.1 (04/2025) 3/28 www.binks.com
EN 22/04/25
Pumps - Maple, DVP, 104009, 104010/LS, 104016, 104027,
104032, 104040/1/2, 104077, 104020-M2, 104023, 104025,
104028/9, 106933, 104205,104149-52, 104207-15, 104147,
104265/66/67.
Suitable for use in hazardous area: Zone 1/Zone 2
Protection Level: Ex h IIB T4 Gb X
Approved body details and role:
Lodging of UKEX Technical file
This Declaration of Conformity / Incorporation is issued
under the sole responsibility of the manufacturer:
Product Description / Object of Declaration:
This Product is designed for use with: Solvent & Waterbased Materials
Binks U.K. Limited,
Ringwood Road,
Bournemouth, BH11 9LH. UK
Signed for and on behalf of Binks
U.K. Ltd:
Document Part No.
.
Element Materials Technology Warwick Ltd. UK. (0891)
Supply of Machinery (Safety) Regulations 2008
Equipment and Protective Systems Intended for use in Potentially Explosive Atmospheres Regulations 2016
by complying with the following statutory documents and designated standards:
BS EN ISO 12100:2010 Safety of Machinery - General Principles for Design
BS EN 12621:2006+2010 Machinery for the supply and circulation of coating materials under pressure - Safety requirements
BS EN ISO 80079-36:2016 Explosive Atmospheres- Part 36:Non Electrical equipment for explosive atmospheres-Basic methods
and requirements.
BS EN ISO 80079-37:2016 Explosive Atmospheres- Part 37: Non Electrical equipment for explosive atmospheres - protection
by methods c, b and k.
BS EN 1127-1:2019 Explosive atmospheres - Explosion prevention - Basic concepts
Providing all conditions of safe use / installation stated within the product manuals have been complied with and also installed in accordance
with any applicable local codes of practice.
F. A. Sutter
UKCA Declaration of Conformity
This Declaration of Conformity / Incorporation is issued under the sole responsibility of the
manufacturer:
Executive President: Engineering and
Operations, Shoreview, MN, 55126. USA
77-3341 R2.1 (04/2025) 4/28 www.binks.com
EN
Read the following warnings before using this equipment.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PROVIDE THIS INFORMATION TO THE
OPERATOR OF THE EQUIPMENT.
NEVER MODIFY THE EQUIPMENT. Do
not modify the equipment unless the
manufacturer provides written
approval.
PROP 65 WARNING. WARNING: This product contains chemicals
known to the state of California to cause cancer and birth defects or
other reproductive harm.
Hazards or unsafe practices which could result in
severe personal injury, death or substantial property
damage.
Important installation, operation or maintenance
information.
WARNING
Hazards or unsafe practices which could result in
minor personal injury, product or property
damage
PINCH POINT HAZARD. Moving parts
can crush and cut. Pinch points are
any areas where ther are moving
parts.
In this part sheet, the words WARNING, CAUTION and NOTE are used to emphasize important safety information as
follows:
WARNING CAUTION NOTE
READ THE MANUAL. Before operating finishing equipment, read and
understand all safety, operation and maintenance information
provided in the operation manual.
AUTOMATIC EQUIPMENT. Automatic
equipment may start suddenly without
warning.
WEAR SAFETY GLASSES. Failure to wear safety glasses with side
shields could result in serious eye injury or blindness.
PROJECTILE HAZARD. You may be
injured by venting liquids or gases that
are released under pressure, or flying
debris.
DE-ENERGIZE, DE-PRESSURISE, DISCONNECT AND LOCK OUT ALL
POWER SOURCES DURING MAINTENANCE. Failure to de-energize,
disconnect and lock out all power supplies before performing
equipment maintenance could cause serious injury or death. KNOW WHERE AND HOW TO SHUT
OFF THE EQUIPMENT IN CASE OF AN
EMERGENCY.
NOISE LEVELS. The A-weighted sound level of pumping and spray
equipment may exceed 85 dB(A) depending on equipment settings.
Actual noise levels are available on request. It is recommended that
ear protection is worn at all times while equipment is in use.
PRESSURE RELIEF PROCEDURE.
Always follow the pressure relief
procedure in the equipment instruction
manual.
INSPECT THE EQUIPMENT DAILY. Inspect the equipment for worn or
broken parts on a daily basis. Do not operate the equipment if you
are uncertain about its condition.
OPERATOR TRAINING. All personnel
must be trained before operating
finishing equipment.
EQUIPMENT MISUSE HAZARD. Equipment misuse can cause the
equipment to rupture, malfunction or start unexpectedly and result in
serious injury. PACEMAKER WARNING. You are in the
presence of magnetic fields which may
interfere with the operation of certain
pacemakers.HIGH PRESSURE CONSIDERATION. High pressure can cause serious
injury. Relieve all pressure before servicing. Spray from the gun,
hose leaks or ruptured components can inject fluid into your body
and cause extremely serious injury.
KEEP EQUIPMENT GUARDS IN PLACE.
Do not operate the equipment if the
safety devices have been removed.
STATIC CHARGE. Fluid may develop a static charge that must be
dissipated through proper grounding of the equipment, objects to be
sprayed and alll other electrically conductive objects in the dispensing
area. Improper grounding or sparks can cause a hazardous condition
and result in fire, explosion or electric shock and other serious injury.
77-3341 R2.1 (04/2025) 5/28 www.binks.com
EN
36:1
Maximum air inlet pressure: 7 bar [101.5 psi]
Maximum fluid pressure: 252 bar [3654 psi]
4.26 l/m [1.125 US gal/m]
Maximum recommended continous cycle rate [cycles/min]:
283 l/m [10 CFM]
Air consumption @ 30 cycles/min and 6.2 bar [90 psi] air
inlet pressure:
Ratio:
595 l/m [20 CFM]
Weight: 29 kg / 63.8 lbs
1'' Sanitary
3/8'' NPT Female
Dirt: 5 microns
Water: +4°C @ 7bar
Oil: 0.1mg/m³
Max. Pump Fluid Inlet Pressure 2 bar [30 psi]
Air Quality ISO 8573.1 Class 3.4.2
# See Note
Specification
Air volume / cycle @ 3.1 bar/45psi: 9.5 l/m [0.33 SCFM]
Air volume / cycle @ 6.2 bar/90psi: 18.5 l/m [0.65 SCFM]
20
Maximum recommended intermittent cycle rate [cycles /
min]:
40
Fluid inlet connection:
Fluid outlet connection:
Compressed Air Inlet 3/8 BSPP / NPSM
Nominal flow volume / cycle: 0.071 l [0.019 US gal]
Output @ 60 cycles / min:
# Note:
Class 3.4.2 Air Quality (Refrigerant dried - water +3ºC@7bar) may be used, however, above 15 cycles/min
optional heavy duty mufflers 192821 or piped exhaust system should be used, if used continuously.
Air consumption @ 15 cycles/min and 6.2 bar [90 psi] air
inlet pressure:
77-3341 R2.1 (04/2025) 6/28 www.binks.com
EN
MOUNTING LOCATIONS
SECTION A-A
Dimensions and Mounting Details
3/8 NPT FEMALE OUTLET
1'' SANITARY INLET
EARTHING POINT
3/8''
BSPP/NPSM
77-3341 R2.1 (04/2025) 7/28 www.binks.com
EN
Mount the pump securely and position the pump at a convenient height (below the lid height of the paint
container), to allow for maintenance, visual observation, and periodic inspection.
The foot mount bracket is included with all pumps.
The foot Mounting bracket must be connected to a suitable earth ground to ensure that there is no possibility of
static build up.
Ground / earth the pump; check resistance is less than 1Ω to achieve true earth ground.
Attach suitable flexible hoses to the inlet and outlet connections.
• SuctionØ15 - 24 I.D. [-1 to 10 bar working pressure]
• OutletØ6-12 I.D. [300 bar working pressure]
Connect a suitable 3/8 NB air hose and 1/2 Pressure Filter Regulator to the air motor.
Select suitable compressed air filter/regulator to required pump performance (see specifications)
Select suitable compressed air feed hose based on air flow required typically:
3/8 NB up to 1.5 l/min fluid flow
1/2 NB greater than 1.5 l/min fluid flow
No additional air lubrication is required as piston ring lubricant is applied during assembly or repair.
If an air lubricator is used then, this must be maintained.
Installation
77-3341 R2.1 (04/2025) 8/28 www.binks.com
EN
Installation
Check all inlet & outlet fittings for tightness
Set the pump speed to a slow cycle rate and prime the pump to remove any air before increasing pressure.
Inspect for any air or fluid leaks.
Set the pump cycle rate to achieve the required paint volume and then adjust the system back pressure regulator
and pump air pressure to achieve the desired system fluid pressure.
A Back Pressure Regulator can be mounted in the paint system return line.
The return line ‘back pressure’ regulator responds to the changes in system fluid flow demand, (due to variable
paint usage) by dynamically adjusting the paint flow rate returning to the system paint tank, thus maintaining the
set pressure.
If an air blow out system is used, never exceed 2 bar [29 psi] on the inlet of the pump.
Do not exceed 5m to the exhaust header pipework.
This product should be flushed with a suitable compatible solvent prior to use.
77-3341 R2.1 (04/2025) 9/28 www.binks.com
EN
2
2
2
2
8
8
8
8
2
2
2
2
2
1
2
1
2
2
2
2
1
2
1
22 195827 ❻
23 195848
18 195810
OUTLET MANIFOLD
SEAT
192551 ❶
13 192777
19 195815
PISTON ASSEMBLY
❷
20 195825
FLUID SEAL ASSEMBLY
21 195826
SERIAL PLATE
14 193360
OUTLET FITTING
⓬
15 193361
INLET MANIFOLD
16 193705 AIR MOTOR ASSEMBLY
17 195809
INLET CYLINDER
ITEM PART NO. DESCRIPTION QTY KIT No.
BALL
❽
8 177141
O-RING
❽
SPRING WASHER
SOCKET HEAD CAP SCREW
❶
4 164838
SOCKET HEAD CAP SCREW
5 165044 ❽
O-RING
6
Pump Assembly
OUTLET CYLINDER
1 0114-014237
RIVET
❷
2 162886
SPRING WASHER
❶
3 162887
165123
SANITARY GASKET
❽
7 177009
9 192009
HEXAGON PLUG
❶⓬
10 192206
O-RING
❶⓬
11 192505
SILENCER
SANITARY CLAMP
❶
12
PLEASE NOTE,
ALL COMPONENTS WITH A KIT NUMBER ARE ONLY AVAILABLE FOR PURCHASE AS PART OF A KIT.
SEE KITS / CONTENTS, PAGES 18 - 21
77-3341 R2.1 (04/2025) 10/28 www.binks.com
EN
Pump Assembly
Grease thread before
assembly
KEY
LOCTITE
TORQUE
MAINTENANCE ORDER
(Reverse for assembly)
GREASE INTERNAL
(AGMD-010)
GREASE
(502735)
77-3341 R2.1 (04/2025) 11/28 www.binks.com
EN
2
1
2
2
4
2
2
2
4
16
4
16
4
4
4
2
2
1
6
2
2
2
2
1
1
2
1
2
PARTS LIST - Air Motor Assembly
CYLINDER STUD ❺ ⓫
20 192762 CYLINDER STUD - LONG ❺ ⓫
21 192763 BELLOWS SPACER ⓭
22 192764
24 192812 EXHAUST ADAPTER
25 192814 BELLOWS LEAK DETECTION HOSE ❸ ❹
26 192815 PUSH IN ELBOW ❹
27 194293 AIR MOTOR PISTON ASSY
28 194599 END PLATE MACHINING
13 165970 M4 PLAIN WASHER ❺
PUMP BRACKET ⓮
23 192799 VENT PLUG
14 165971 M4 SPRING WASHER ❺
15 177038 M10 x 12 BUTTON HEAD CAP SCREW ❺ ⓮
16 192374 RETAINING NUT ⓭
17 192579 KNIFED BELLOWS ❼
18 192757 AIR CYLINDER
19 192761
8 162704 SHAFT BEARING ❸ ❹
9 163920 M6 x 30 SOCKET HEAD CAP SCREW ❺
10 165108 M8 SPRING WASHER ❺ ⓫
11 165528 M4 x 16 SOCKET HEAD CAP SCREW ❺
12 165963 M8 DOME NUT ❺ ⓫
3 161992 Ø117.5 x 2.62 O-RING ❸ ❹
4 161993 Ø20.35 x 1.78 O-RING ❸ ❹
5 161994 Ø4.47 x 1.78 O-RING ❸ ❹
6 161995 Ø19.5 x 3.00 O-RING ❸ ❹
7 162703 SHAFT SEAL ❸ ❹
ITEM PART NO. DESCRIPTION QTY REMARKS
1 0115-010037 POPPET ASSEMBLY ❾ ❿
2 0115-010102 AIR VALVE ASSEMBLY
PLEASE NOTE,
ALL COMPONENTS WITH A KIT NUMBER ARE ONLY AVAILABLE FOR PURCHASE AS PART OF A KIT.
SEE KITS / CONTENTS, PAGES 18 - 21
77-3341 R2.1 (04/2025) 12/28 www.binks.com
EN
Air Motor Assembly
K
E
Y
L
O
C
T
IT
E
T
O
R
Q
U
E
M
A
IN
T
E
N
A
N
C
E
O
R
D
E
R
(R
e
v
e
rs
e
f
o
r
a
s
s
e
m
b
ly
)
G
R
E
A
S
E
I
N
T
E
R
N
A
L
(A
G
M
D
-0
1
0
)
G
R
E
A
S
E
(5
0
2
7
3
5
)
IT
E
M
7
D
E
T
A
IL
77-3341 R2.1 (04/2025) 13/28 www.binks.com
EN
1
1
2
1
M12 x 40 GRUB SCREW
194293 - Air Motor Piston Assembly
4 192760
PISTON SHAFT
KIT No.QTYDESCRIPTIONPART NO.ITEM
1 162702 ❸ ❹
2 165964
AIR MOTOR PISTON SEAL
3 192759
PISTON
PLEASE NOTE,
ALL COMPONENTS WITH A KIT NUMBER ARE ONLY AVAILABLE FOR PURCHASE AS PART OF A KIT.
SEE KITS / CONTENTS, PAGES 18 - 21
KEY
LOCTITE
TORQUE
MAINTENANCE ORDER
(Reverse for assembly)
GREASE INTERNAL
(AGMD-010)
GREASE
(502735)
77-3341 R2.1 (04/2025) 14/28 www.binks.com
EN
1
1
6
2
2
2
2
2
2
8
1
1
1
2
12
0115-010107
UNIVERSAL FITTING
0115-010015 SPOOL AND SLEEVE ASSEMBLY
ITEM PART NO. DESCRIPTION
162789
VALVE BLOCK END CAP
❾
3 0115-010016 BUMPER
4 0115-010017 MAGNET
❾
5 0115-010018
❾
6 0115-010020 DIAPHRAGM
1.5 x 36 O-RING
❸
8 0115-010049 2 x 20 O-RING
❸
1
2
SPOOL AND SLEEVE O-RING
1/4 BSPP PIPE PLUG
1/8 BSPT PIPE PLUG
13
180584
VALVE BLOCK
192813 QUICK EXHAUST VALVE CAGE
9 0115-010073
7 0115-010021
10 0115-010097
11
M4 x 12 BUTTON HEAD CAP SCREW
❾
0114-014657
0115-010102 - Air Valve Assembly
QTY KIT No.
KEY
LOCTITE
TORQUE
MAINTENANCE ORDER
(Reverse for assembly)
GREASE INTERNAL
(AGMD-010)
GREASE
(AGMD-010)
MAGNET HAZARD
77-3341 R2.1 (04/2025) 15/28 www.binks.com
EN
1
1
1
1
1
1
1
195804 FLUID PISTON
195815
BALL
❷
PART NO. DESCRIPTION QTY
SEAT
ITEM KIT No.
162889
O-RING
❶
4 193795
O-RING
❷
195813 PISTON KEEP
5
1 0114-014237
SPRING
❷
2 162886 ❶
3
PLEASE NOTE,
ALL COMPONENTS WITH A KIT NUMBER ARE ONLY AVAILABLE FOR PURCHASE AS PART OF A KIT.
SEE KITS / CONTENTS, PAGES 18 - 21
6
7
195825 - Fluid Piston Assembly
Use a 18mm Single Hex Socket
when tightening or removing ball
cage from Piston.
KEY
LOCTITE
TORQUE
MAINTENANCE ORDER
(Reverse for assembly)
GREASE INTERNAL
(AGMD-010)
GREASE
(502735)
77-3341 R2.1 (04/2025) 16/28 www.binks.com
EN
NOTES
77-3341 R2.1 (04/2025) 17/28 www.binks.com
EN
Pump will not ‘Prime’
Air getting into the suction hose/manifold Check seals and hose connections.
Worn piston seal. Replace piston seals.
Ball checks not seating correctly.
Inspect, clean and/or replace balls
and seats.
Pump will not run
QE diaphragm defective.
Check for constant exhaust air when
pump is not running. Check/replace
QE diaphragms.
Symptom Possible Cause Remedy
Replace piston seal.
Check clean/replace Air valve.
Air piston seal worn.
Ball checks not seating correctly.
Inspect, clean and/or replace balls
and seats.
No air or fluid supply
Check air and fluid supply ball valves
and supply hoses.
Pilot valve assemblies inoperable.
Switch/interchange pilot valves to
isolate faulty pilot valve and
clean/replace.
Pilot valve assemblies inoperable.
Fault Finding
77-3341 R2.1 (04/2025) 18/28 www.binks.com
EN
Air getting into fluid line, air supply restricted.
Check seals and hose connections.
Check air supply
Obstructed fluid ball checks.
Remove, clean, and inspect seat,
ball, and ball cage. Replace if
suspect or worn.
Pump runs but has
excessive pulsation.
Worn fluid piston seal. Replace fluid piston seal.
Air exhaust restricted.
Check QE diaphragms and exhaust
outlets.
Symptom Possible Cause Remedy
Worn air motor piston seals. Replace air motor piston seal.
Worn/failed air motor shaft seals.
Disassemble pump as required to
replace air motor shaft seals.
Paint leaking into
detection hose, air
bleeding from vent
plug
Bellows seal failure Replace bellows seal
Air motor shaft seal leaking
Check air motor shaft seal replace as
necessary
Fault Finding
77-3341 R2.1 (04/2025) 19/28 www.binks.com
EN
192551
192505
192206
O-RING
O-RING
O-RING
161994
161993
GLYDE RING ASSEMBLY
SEAL
HOSE
DIAPHRAGM
162886
QTY
O-RING - PTFE
O-RING - PTFE
SANITARY GASKET
DESCRIPTION
250850 (❻)
250848 - FLUID SECTION SEAL KIT❶
162889
162887
2
2
SEAT
BALL
FLUID SECTION SEAL KIT
DESCRIPTION
DESCRIPTIONPART NO.
0114-014237
250848 (❶)
PART NO.
PART NO.
O-RING - PTFE
2
FLUID PISTON SEAL KIT
PLUG
O-RING - PTFE
Spares Kits for Maple 3/36 Pump
2
2
2
4
4
4
2
2
O-RING
SPRING
2
2
QTY
1
2
2
1
2O-RING
BEARING
4
1
QTY
1
250849 - FLUID OVERHAUL KIT
250618 - AIR MOTOR SEAL KIT
195815
2KNIFED BELLOWS192579
193795
161992
0115-010021
0115-010020
192814
162704
162703
162702
161995
❷
❸
77-3341 R2.1 (04/2025) 20/28 www.binks.com
EN
❹
250850 - FLUID PISTON SEAL KIT
250877 - MAPLE AIR MOTOR FIXINGS KIT
250876 - AIR MOTOR OVERHAUL KIT
DESCRIPTION
AIR MOTOR FIXINGS KIT
AIR MOTOR AIR VALVE CONTROL KIT
POPPET KIT - 1 PUMP
QTY
1
1
1
QTY
4
16
4
16
4
4
4
6
DESCRIPTION
SPRING WASHER
SPRING WASHER
2
Spares Kits for Maple 3/36 Pump
0115-010037-K2
250628 (❾)
250877 (❺)
PART NO.
O-RING
O-RING
O-RING
O-RING
BEARING
SEAL
192814
DOME NUT
BELLOWS LEAK DETECTION HOSE
GLYDE RING ASSEMBLY
2
162703
162704
161995
161994
161993
161992
PART NO.
163920
165108
165528
165963
165970
165971
177038
192761
192815 ELBOW
❻
❺
4
2
2
2
2
1
1162702
PART NO.
162799 2
QTY
2
162908 PISTON SEAL 2
CAP HEAD SCREW
CAP HEAD SCREW
DESCRIPTION
O-RING
PLAIN WASHER
BUTTON HEAD CAP SCREW
CYLINDER STUD
CYLINDER STUD - LONG192762 2
162907 PISTON SEAL
77-3341 R2.1 (04/2025) 21/28 www.binks.com
EN
192579-K2 - KNIFED BELLOWS KIT
250856 - FLUID SECTION FIXINGS KIT
250628 - AIR MOTOR CONTROL VALVE KIT
0115-010037-K2 - POPPET KIT - 1 PUMP
0115-010037-K10 - POPPET KIT - 5 PUMP❿
❿
❾
❽
❼
DESCRIPTION
Spares Kits for Maple 3/36 Pump
177141
177009
KNIFED BELLOWS
PART NO.
192579
QTYDESCRIPTIONPART NO.
0115-010049
0115-010037
0115-010017
0115-010016
0115-010015
PART NO.
POPPET ASSEMBLY
SPRING WASHER
8
8
8
SPOOL AND SLEEVE ASSEMBLY 1
SOCKET HEAD CAP SCREW
SOCKET HEAD CAP SCREW
165044
2
QTY
165123 SPRING WASHER 8
POPPET ASSEMBLY
0115-010037
PART NO.
0115-010037
PART NO.
2
DESCRIPTION
DESCRIPTION QTY
DESCRIPTION QTY
QTY
2
2
2
2MAGNET
O-RING
BUMPER
10POPPET ASSEMBLY
77-3341 R2.1 (04/2025) 22/28 www.binks.com
EN
250872 CYLINDER STUD KIT
⓮
⓭
⓬
⓫
192009
2
2
QTY
16
DESCRIPTIONPART NO.
165108
165963
192762
192761
PART NO.
4
2
QTY
2
2
6
QTY
BUTTON HEAD CAP SCREW
PUMP BRACKET
DESCRIPTION
BELLOWS NUT
SPACER
SPRING WASHER
CYLINDER STUD - LONG
CYLINDER STUD
DESCRIPTION
DOME NUT
250875 BRACKET FIXING KIT
1
2
QTYDESCRIPTION
INLET MANIFOLD
SANITARY GASKET
SANITARY CLAMP
177038
192764
PART NO.
192374
192763
PART NO.
193360
192206
250874 BELLOW FIXING KIT
250873 INLET MANIFOLD KIT
16
Spares Kits for Maple 3/36 Pump
77-3341 R2.1 (04/2025) 23/28 www.binks.com
EN
BELLOWS ASSEMBLY SPIGOT
QTYDESCRIPTIONPART NO.ITEM
Bellows Replacement
1 502769
2 502382
Screw Item No. 2 (assembly spigot) onto the
piston shaft
Using Item No. 1, push bellows over spigot
until located in groove.
Thread nut onto bellows ensuring the thread
starts squarely.
Smear loctite 572 over nose of bellows,
thread nut onto bellows ensuring the thread
starts squarely. Grip bellows lightly by hand
and tighten the nut with a 1 A/F spanner
until the nut contacts the bellows shoulder.
1
1BELLOWS POSITIONING TOOL
1 2
77-3341 R2.1 (04/2025) 24/28 www.binks.com
EN
502375 SKF LGWA2 Bearing grease 240ml Cartridge
192779 EXHAUST TUBE ADAPTER (1 NB HOSE) FOR PIPED EXHAUST
192820 EXHAUST TUBE ADAPTER (1.5 NB HOSE) FOR PIPED EXHAUST
192803 MANIFOLD PLUG FOR PIPED EXHAUST
192009 SANITARY CLAMP
192821 HEAVY DUTY MUFFLERS
FOR SHAFT SEAL (7)
502769 BELLOWS POSITIONING TOOL
194281
193275
ITEM
KLUBER ISOFLEX TOPAS NB 52 GREASE
1'' SANITARY - 1'' NPT (f) ADAPTER
50ml TUBE
REMARKS
192206
502382
502608
AGMD-010
ACCESSORIES
SANITARY GASKET
BELLOWS ASSEMBLY SPIGOT
SEAL INSERTION TOOL
PART NO.
1'' SANITARY - 3/4'' NPT (f) ADAPTER
77-3341 R2.1 (04/2025) 25/28 www.binks.com
EN
NOTES
77-3341 R2.1 (04/2025) 26/28 www.binks.com
EN
WARRANTY POLICY
This product is covered by Binks materials and workmanship limited warranty.
The use of any parts or accessories, from a source other than Binks, will void all
warranties. Failure to reasonably follow any maintenance guidance provided, may
invalidate any warranty.
For specific warranty information please contact Binks.
For technical assistance or to locate an authorised distributor, contact one of our
international sales and customer support locations below.
REGION BINKS CONTACT
Americas Tel: 1-888-992-4657
Europe, Africa, Middle East Tel: +44 (0)1202 571 111
India marketingroa@binks.com
China Tel: +8621-3373 0108
Korea Tel: +82313663303
Japan Tel: +81 45 785 6421
Australia Tel: +61 (0) 2 8525 7555
WARRANTY PAGE
77-3341 R2.1 (04/2025) 27/28 www.binks.com
EN
Binks is a global leader in innovative finishing technologies. Binks reserves the right to modify
equipment specifications without prior notice.
Binks®, DeVilbiss®, and Ransburg® are registered trademarks of Binks US, LLC.
© 2025 Binks US, LLC. All rights reserved.
77-3341 R2.1 (04/2025) 28/28 www.binks.com
