Resource Library
QuickHeat Hose Center Clamp Assembly Kit Manual 347552
- QuickHeat Hose Center Clamp Assembly Kit Manual 347552 [ English ]
347552
®
CENTER CLAMP ASSEMBLY KIT: 347526
INSTALLATION GUIDE
PARTS/TOOLS:
Item Description Qty
a A HOSE CLAMP, OUTSIDE 1
b A HOSE CLAMP, INSIDE 1
c B HOSE CLAMP, OUTSIDE 1
d B HOSE CLAMP, INSIDE 1
e M5X0.8 X 30 TAMPER RESISTANT SCREW 4
f BUTTON HEAD HEX DRIVE SCREW 2
g M5X0.8 PRESS FIT NUT 2
h TAMPER RESISTANT TORX BIT 1
I 3MM ALLEN WRENCH 1
EN
www.binks.com347552 REV C (05/2025) © Binks US, LLC. All Rights Reserved
Clamp Removal
1. Turn off power to equipment
2. Remove any necessary hose wrap and debris to
expose clamps that need replacing.
NOTE: Be careful not to nick or cut cables, material
hoses, or any other component in hose bundle.
3. Identify and remove necessary clamps from hose
using 3mm Allen wrench and special Torx bit
(provided).
Clamp Installation:
NOTE: Clamps are located near the modems. Refer to
Fig. 1 for complete diagram of clamp locations.
4. Mark hose where clamp will be installed (See
measurements in Fig. 1)
5. Install two A Clamp pieces by sandwiching them
around the A material hose.
NOTE: Keep clamp square with nearest modem when
installing.
ELECTRICAL SHOCK HAZARD: Disconnect
all power sources before accessing any
electrical connections in the Control Module,
Fluid Modules, or hoses. Equipment must be
serviced by trained personnel only.
FIRE AND EXPLOSION HAZARD: Improper
equipment grounding, poor ventilation, open
flame or sparks can cause a hazardous
condition and result in fire or explosion and
serious injury.
NEVER MODIFY THE EQUIPMENT:
Do not modify the equipment unless the
manufacturer provides written approval.
WARNING
Read the following warnings before performing any
maintenance
CLAMP LOCATION
Fig. 1
EN
www.binks.com 347552 REV C (05/2025)© Binks US, LLC. All Rights Reserved
6. Repeat step 5 with B clamp pieces.
7. Align A clamp pieces and B clamp pieces by
loosely installing long screws through both clamp
sets. (Fig. 3)
NOTE: Loosely installing long screws ensures that
clamp halves are aligned correctly when crimped
onto master hose.
8. With long screws loosely installed, assemble clamps
by installing (4X) Torx screws (Fig. 4)
NOTE: When installing Torx screws, alternate
tightening between top screw and bottom screw to
ensure even clamping pressure. Tighten until clamp
halves touch.
9. Clamp should look like Fig. 5.
10. Remove long screws from clamp and install power
cables (not shown) through the center guide in clamp
(Fig. 6).
11. Re-install long screws and tighten using 3mm Allen
wrench.
Fig. 2
Fig. 3
Fig. 2
Fig. 5
Fig. 6
WARRANTY POLICY
This product is covered by Binks’ materials and workmanship limited warranty.
The use of parts or accessories from sources other than Binks will void all
warranties. Failure to follow reasonable maintenance guidance provided can
invalidate the warranty.
For specific warranty information, please contact Binks.
For technical assistance or to locate an authorized distributor, contact one of our
international sales and customer support locations listed below.
REGION BINKS CONTACT
Americas Tel: 1-800-992-4657
Europe, Africa, Middle East Tel: +4401202571111
India marketingroa@binks.com
China Tel: +862133730108
Korea Tel: +82313663303
Japan Tel: +81457856421
Australia Tel: +61085257555
WARRANTY PAGE
Binks is a global leader in innovative finishing technologies.
Binks reserves the right to modify equipment specifications without prior notice.
Binks®, DeVilbiss® and Ransburg® are registered trademarks of Binks US, LLC.
