- FX115 Fluid Section Manual 77-3277 FR [ English ]
77-3277
FX115
Fluid Section
FX115PU-SMX
EN
IMPORTANT! DO NOT DESTROY
It is the Customer's responsibility to have all operators and service personnel read and
understand this manual.
Contact your local Binks representative for additional copies of this manual.
READ ALL INSTRUCTIONS BEFORE OPERATING THIS PRODUCT
ADDITIONAL RESOURCES
For additional information or copies of your service manual, please visit us online at:
binks.com/en/library
Or use this QR code with your mobile device:
XXXXXXXX
Insert
QR
code
Obey local or municipal regulations for product recycling and disposal.
77-3277 R2.0 (07/2025) 2/16 www.binks.com
EN
Product Description / Object of Declaration:
This Product is designed for use with: Solvent & Waterbased Materials
Representative authorised to compile the technical file President @. Binks France SAS
5 Place Pierre Semard, 94130 Nogent sur Marne , Paris, France
Fluid Sections FX220XX-XXX, FX440XX-XXX, FX880XX-XXX,
FX115XX-XXX, FX122XX-XXX, FX190XX-XXX, FX420XX-XXX,
FX68XX-XXX, FX860XX-XXX.
Suitable for use in hazardous area: Zone 1/Zone 2
Protection Level: II 2 G X/Ex h IIB Gb T4 X
EU Declaration of Conformity
This Declaration of Conformity / Incorporation is issued under the sole responsibility of the
manufacturer:
F. A. Sutter
20/05/25
Machinery Directive 2006/42/EC
ATEX Directive 2014/34/EU
by complying with the following statutory documents and harmonised standards:
EN ISO 4413:2010 Hydraulic Fluid Power - General Rules and safety requirements
EN ISO 4414:2010 Pneumatic Fluid Power - General Rules and safety requirements
EN ISO 12100:2010 Safety of Machinery - General Principles for Design
EN 12621:2006+2010 Machinery for the supply and circulation of coating materials under pressure - Safety requirements
EN ISO 80079-36:2016 Explosive Atmospheres- Part 36:Non Electrical equipment for explosive atmospheres-Basic methods
and requirements.
EN ISO 80079-37:2016 Explosive Atmospheres- Part 37: Non Electrical equipment for explosive atmospheres - protection by
methods c, b and k.
EN 1127-1:2019 Explosive atmospheres - Explosion prevention - Basic concepts
Providing all conditions of safe use / installation stated within the product manuals have been complied with and also installed in accordance
with any applicable local codes of practice.
Signed for and on behalf of Binks
U.K. Ltd:
Executive President: Engineering and
Operations, Shoreview, MN, 55126. USA
Notified body details and role: Element Materials Technology Rotterdam B.V. (2812)
Lodging of ATEX Technical file
This Declaration of Conformity / Incorporation is issued
under the sole responsibility of the manufacturer:
Binks U.K. Limited,
Ringwood Road,
Bournemouth, BH11 9LH. UK
Document Part No.
.
77-3277 R2.0 (07/2025) 3/16 www.binks.com
EN
Product Description / Object of Declaration:
This Product is designed for use with: Solvent & Waterbased Materials
Element Materials Technology Warwick Ltd. UK. (0891)
UKCA Declaration of Conformity
Fluid Sections FX220XX-XXX, FX440XX-XXX, FX880XX-XXX,
FX115XX-XXX, FX122XX-XXX, FX190XX-XXX, FX420XX-XXX,
FX68XX-XXX, FX860XX-XXX.
Signed for and on behalf of Binks
U.K. Ltd:
Suitable for use in hazardous area: Zone 1/Zone 2
This Declaration of Conformity / Incorporation is issued under the sole responsibility of the
manufacturer:
Supply of Machinery (Safety) Regulations 2008
Equipment and Protective Systems Intended for use in Potentially Explosive Atmospheres Regulations 2016
by complying with the following statutory documents and designated standards:
BS EN ISO 4413:2010 Hydraulic Fluid Power - General Rules and safety requirements
BS EN ISO 4414:2010 Pneumatic Fluid Power - General Rules and safety requirements
BS EN ISO 12100:2010 Safety of Machinery - General Principles for Design
BS EN 12621:2006+2010 Machinery for the supply and circulation of coating materials under pressure - Safety requirements
BS EN ISO 80079-36:2016 Explosive Atmospheres- Part 36:Non Electrical equipment for explosive atmospheres-Basic methods
and requirements.
BS EN ISO 80079-37:2016 Explosive Atmospheres- Part 37: Non Electrical equipment for explosive atmospheres - protection
by methods c, b and k.
BS EN 1127-1:2019 Explosive atmospheres - Explosion prevention - Basic concepts
Providing all conditions of safe use / installation stated within the product manuals have been complied with and also installed in accordance
with any applicable local codes of practice.
Executive President: Engineering and
Operations, Shoreview, MN, 55126. USA
F. A. Sutter
20/05/25
Protection Level: II 2 G X/Ex h IIB Gb T4 X
Approved body details and role:
Lodging of UKEX Technical file
This Declaration of Conformity / Incorporation is issued
under the sole responsibility of the manufacturer:
Binks U.K. Limited,
Ringwood Road,
Bournemouth, BH11 9LH. UK
Document Part No.
.
77-3277 R2.0 (07/2025) 4/16 www.binks.com
EN
CAUTION NOTE
DE-ENERGIZE, DE-PRESSURISE, DISCONNECT AND LOCK OUT ALL
POWER SOURCES DURING MAINTENANCE. Failure to de-energize,
disconnect and lock out all power supplies before performing
equipment maintenance could cause serious injury or death. KNOW WHERE AND HOW TO SHUT
OFF THE EQUIPMENT IN CASE OF AN
EMERGENCY.
NOISE LEVELS. The A-weighted sound level of pumping and spray
equipment may exceed 85 dB(A) depending on equipment settings.
Actual noise levels are available on request. It is recommended that
ear protection is worn at all times while equipment is in use.
PRESSURE RELIEF PROCEDURE.
Always follow the pressure relief
procedure in the equipment instruction
manual.
In this part sheet, the words WARNING, CAUTION and NOTE are used to emphasize important safety information as
follows:
WARNING
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PROVIDE THIS INFORMATION TO THE
OPERATOR OF THE EQUIPMENT.
Hazards or unsafe practices which could result in
severe personal injury, death or substantial property
damage.
Hazards or unsafe practices which could result in
minor personal injury, product or property
damage
Important installation, operation or maintenance
information.
WARNING
Read the following warnings before using this equipment.
STATIC CHARGE. Fluid may develop a static charge that must be
dissipated through proper grounding of the equipment, objects to be
sprayed and alll other electrically conductive objects in the dispensing
area. Improper grounding or sparks can cause a hazardous condition
and result in fire, explosion or electric shock and other serious injury.
NEVER MODIFY THE EQUIPMENT. Do
not modify the equipment unless the
manufacturer provides written
approval.
PROP 65 WARNING. WARNING: This product contains chemicals
known to the state of California to cause cancer and birth defects or
other reproductive harm.
READ THE MANUAL. Before operating finishing equipment, read and
understand all safety, operation and maintenance information
provided in the operation manual.
AUTOMATIC EQUIPMENT. Automatic
equipment may start suddenly without
warning.
WEAR SAFETY GLASSES. Failure to wear safety glasses with side
shields could result in serious eye injury or blindness.
INSPECT THE EQUIPMENT DAILY. Inspect the equipment for worn or
broken parts on a daily basis. Do not operate the equipment if you
are uncertain about its condition.
OPERATOR TRAINING. All personnel
must be trained before operating
finishing equipment.
EQUIPMENT MISUSE HAZARD. Equipment misuse can cause the
equipment to rupture, malfunction or start unexpectedly and result in
serious injury. PACEMAKER WARNING. You are in the
presence of magnetic fields which may
interfere with the operation of certain
pacemakers.HIGH PRESSURE CONSIDERATION. High pressure can cause serious
injury. Relieve all pressure before servicing. Spray from the gun,
hose leaks or ruptured components can inject fluid into your body
and cause extremely serious injury.
KEEP EQUIPMENT GUARDS IN PLACE.
Do not operate the equipment if the
safety devices have been removed.
PINCH POINT HAZARD. Moving parts
can crush and cut. Pinch points are
any areas where ther are moving
parts.
PROJECTILE HAZARD. You may be
injured by venting liquids or gases that
are released under pressure, or flying
debris.
77-3277 R2.0 (07/2025) 5/16 www.binks.com
EN
Ram - Chop Check
PTFE + UHMWPE
PTFE + UHMWPE
Rod Upper Packing Seal Options
Rod Lower Packing Seal Options
Rod Surface Treatment
127mm (5)
Ratio with AX160L Air motor (MX11543 Pump Assembly) 43:1
SMX
1/2 NPT
10 Kg (22 lbs)
Fluid Outlet
Weight
PU
Ceramic Coated
Fluid Section designed to be used with AX160L & AX200L Air Motors –
MX1154PU-SMX & MX11568PU-SMX
See Pump Manual MX115 for installation details
PU
Recommended intermittent cycle rate 20 cycles/min
Flow at 60 cycles/min 6.9 l/m [1.8 US gal/m]
Flow per cycle 0.115 l [0.03 US gal]
SPECIFICATION
Fluid Inlet
Ratio with AX200L Air Motor (MX11568 Pump Assembly) 68:1
Maximum Fluid Pressure 500 bar (7250 psi)
Nominal pump stroke
77-3277 R2.0 (07/2025) 6/16 www.binks.com
EN
FX115PU-SMX
77-3277 R2.0 (07/2025) 7/16 www.binks.com
EN
FX115PU-SMX
77-3277 R2.0 (07/2025) 8/16 www.binks.com
EN
1
1
1
1
1
2
1
1
2
1
1
2
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
15
Ø72.69 x 2.62 O'RING VITON162839
M10 SPRING WASHER
SHOVEL PLATE BALL193781
RAM ADAPTOR193778
193788
FX115 UPPER SEAT RETAINER
FX115 LOWER PACKING SET
194117
162803
162804
162825
SHAFT BEARING
LIP SEAL
Ø46 x 3 O’RING PTFE
TOP SHOVEL PLATE
193782 BALL CHECK INSERT
FX122/FX115 UPPER PACKING SET
194116
32
33
FX115 SHOVEL SHAFT
FX115 PUMP ROD
22
23
18
12
13
14
19411435
37
38
39
40 194471 PRIMER KIT ASSEMBLY
194118
194119
FX115/122 INLET TUBE
SEAL
34
193783 BALL CHECK SEAT
193784 BOTTOM SHOVEL PLATE
193785
LOWER PLATE LOCK24
194088
FX115/122 UPPER PUMP TUBE
25
FX115/122 PACKING NUT
26
PACKING RETAINER
COMPRESSION WASHER
FX115/122 LOWER PUMP TUBE
194093
194094 ADAPTER PLATE
PACKING SPRING
194097
194098
27
194096
16
17
193189
165988 M10 x 30 CAPHEAD SCREW
1
29 194092
28
UPPER PLATE LOCK
193786
19
193787
20
21
3 0115-010140 FX12 LOWER BALL CAGE SEAL
4 0115-010642 NAMEPLATE BINKS INDUSTRIAL
5 161502 Ø12.1 x Ø1.6 O'RING PTFE
193776 FX68 & 72 LOWER BALL CAGE
10
164838 No 2 x 4.75 RIVET
11
PISTON SEAT
162745 Ø29.9 X 1.78 O'RING PTFE
163320 M6 HEX NUT
7
8
9
0114-014056 VALVE SEAT
Parts list - FX115PU-SMX Fluid Section
PART NO.ITEM REMARKSQTY
6
DESCRIPTION
0114-014237 15mm DIAMETER BALL2
165123
SLIP FLANGE193752
193794
30
31
36
77-3277 R2.0 (07/2025) 9/16 www.binks.com
EN
3
1
3
1
1
3
3
1
Parts list - Item 28 - Upper Packing Assembly - 194088
ITEM PART NO. DESCRIPTION QTY REMARKS
50 0114-013972 FX12 UPPER PACKING PTFE
FX68 LOWER PACKING UHMWPE
FX68 LOWER PACKING PTFE
FX68 LOWER FEMALE ADAPTER
Parts list - Item 39 - Lower Packing Assembly - 194119
ITEM PART NO. DESCRIPTION QTY REMARKS
FX12 UPPER FEMALE ADAPTER
FX12 UPPER PACKING UHMW
UPPER MALE ADAPTER
0115-010150
0115-010267
194091
51
52
53
55
56
57
58
193972
193975
193974
193973
FX68 LOWER MALE ADAPTER
77-3277 R2.0 (07/2025) 10/16 www.binks.com
EN
1
1
2
1
1
2
1
1
1
1
1
26 193788 COMPRESSION WASHER
27 193794 SEAL
28 194088 FX122/FX115 UPPER PACKING SET
39 194119 FX115 LOWER PACKING SET
8 162804 LIP SEAL
9 162825 Ø47 x 3 O’RING PTFE
10 162839 Ø72.69 x 2.62 O'RING VITON
5 161502 Ø12.1 x Ø1.6 O'RING PTFE
6 162745 Ø29.9 X 1.78 O'RING PTFE
7 162803 SHAFT BEARING
3
FX115 Spare Parts Kit
Spare Parts Kit
250718
FX115PU-SMX
ITEM PART NO. DESCRIPTION QTY REMARKS
0115-010140 FX12 LOWER BALL CAGE SEAL
Stop the pump and relieve all material
pressure. Tighten the packing nut until the
resistance of the packings clamping the shaft
can be felt. Do not over-tighten. Ensure
solvent cup has the correct lubricant for the
material being pumped present at all times.
Seal wear or damage to packing
material
Leak from rod seal packings
Damaged rod Replace
Contaminates trapped between ball
and seat
Strip and clean pump.
Check for damage
Worn or damaged balls/seats Check for wear; replace balls and / or seats.
Loose joint on suction side Replace
Low material flowrate, pump
running fast or will not stall
(stalling - 1 stroke should not
occur in less than 30
seconds)
Air entering system Loose joint on suction side Check and reseal fittings
Fault Finding
Problem Cause Action
77-3277 R2.0 (07/2025) 11/16 www.binks.com
EN
1.
2.
3.
4.
5.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Use the ‘C’ spanner to tighten the packing nut (32) and preload the chevron packing, approximate torque
40Nm.
Add a compatible lubricant to the solvent cup of the packing nut (32).
Stop the pump at the bottom stroke position.
Disconnect fluid section to air motor coupling.
Use ‘C’ spanners to remove the packing nut (32) from the packing retainer.
Remove all parts and clean using compatible solvent, discard the 6 off chevron packings.
Refit male packing retainer (53) into packing retainer (34). Lubricate the bore with compatible grease and
fit 1 off new chevron packings assembly (28).
Lubricate the thread of the packing nut (32) with anti-seize and fit into the packing retainer (34), hand
tighten only.
Use the ‘C’ spanner to tighten the packing nut (32) and preload the chevron packing, approximate torque
40Nm.
Couple the air motor to the fluid section.
Run the pump at pressure then de-pressurise again, retighten packing nut (32)
Upper Packing Replacement
Preventative Maintenance - Pump Paint Packings
Check daily to ensure that there is the correct type of lubricant material present in the solvent cup; this should
be compatible with the material being pumped. Confirmation from the material supplier should be sought to
ensure compatibility to prevent the risk of contamination.
A universal lubricant is available - Wet Sol ‘Plus’ Binks Part Number 863009
Check daily for excessive material leaks into the solvent cup.
Upper Packing Adjustment
Stop the Pump and isolate the air motor air supply.
Relieve all fluid pressure from the pump.
Clean the solvent cup to remove excess leaked material.
Relieve all fluid pressure from the pump.
Carefully start the air motor with reduced air pressure and stop at the top stoke position. Isolate the air
supply to the air motor.
Refit the solvent cup.
Carefully drive the air motor shaft down towards the fluid section.
77-3277 R2.0 (07/2025) 12/16 www.binks.com
EN
NOTES
77-3277 R2.0 (07/2025) 13/16 www.binks.com
EN
NOTES
77-3277 R2.0 (07/2025) 14/16 www.binks.com
EN
Tel: +44 (0)1202 571 111
India marketingroa@binks.com
WARRANTY POLICY
This product is covered by Binks materials and workmanship limited warranty.
The use of any parts or accessories, from a source other than Binks, will void all
warranties. Failure to reasonably follow any maintenance guidance provided, may
invalidate any warranty.
Europe, Africa, Middle East
For specific warranty information please contact Binks.
China Tel: +8621-3373 0108
Korea Tel: +82313663303
Japan Tel: +81 45 785 6421
Australia
WARRANTY PAGE
For technical assistance or to locate an authorised distributor, contact one of our
international sales and customer support locations below.
REGION BINKS CONTACT
Tel: +61 (0) 2 8525 7555
Americas Tel: 1-888-992-4657
77-3277 R2.0 (07/2025) 15/16 www.binks.com
EN
Binks is a global leader in innovative finishing technologies. Binks reserves the right to modify
equipment specifications without prior notice.
Binks®, DeVilbiss®, and Ransburg® are registered trademarks of Binks US, LLC.
© 2025 Binks US, LLC. All rights reserved.
77-3277 R2.0 (07/2025) 16/16 www.binks.com
